Humminbird MEGA Live Manual Download Page 47

Page: 47 / 75

Cable Installation

COM (communications)

transducer

power

Ethernet

NMEA 2000

HELIX G4N 8, 9, 10, 12, 15 Cable Tray

4. Connect Power

Power:

Route the power cable(s) to the main switch or fuse panel (usually

located near the console). If you must connect to a battery, connect to a battery
switch (not included).

WARNING!

The MEGA Live Imaging TargetLock and MEGA 360 Imaging

transducers should be connected to a main switch, fuse panel, or battery
switch. Humminbird does not recommend connecting to a battery without a
fuse and a switch.

CAUTION:

Some boats have 24 or 36 Volt electric systems, but the MEGA

Live Imaging transducer MUST be connected to a 12 VDC power supply.

NOTE:

Humminbird is not responsible for over-voltage or over-current failures.

The MEGA Live Imaging TargetLock must have adequate protection through the
proper selection and installation of a 5A slow-blow fuse.

NOTE:

A 10' (3 m) power cable is included to supply power to the MEGA LIVE

Imaging transducer. You may shorten or lengthen the cable using 12 gauge
multi-stranded copper wire.

Summary of Contents for MEGA Live












































































Search results

Summary of Contents for MEGA Live

Reviews:

Related manuals for MEGA Live

Brands by name

Popular brands

Humminbird MEGA Live, Manual

Search results

Summary of Contents for MEGA Live

Reviews:

Related manuals for MEGA Live

Brands by name

Popular brands