Humminbird MEGA Live Manual Download | Manualshive

Page: 3 / 75

background image

NOTE:

The illustrations in this manual may not look the same as your product, but

your unit will function in a similar way.

NOTE:

To purchase accessories for your control heads, visit our Web site at

humminbird.com

or Contact Humminbird Technical Support through our Help Center

at

https://humminbird-help.johnsonoutdoors.com/hc/en-us

.

NOTE:

The procedures and features described in this manual are subject to change

without notice. This manual was written in English and may have been translated to
another language. Humminbird is not responsible for incorrect translations or
discrepancies between documents.

NOTE:

Product specifications and features are subject to change without notice.

NOTE:

Humminbird verifies maximum stated depth in saltwater conditions, however

actual depth performance may vary due to transducer installation, water type, thermal
layers, bottom composition, and slope.

WARNING

THIS PRODUCT CONTAINS A BUTTON BATTERY.

If swallowed, a lithium button battery can cause severe or fatal injuries within
2 hours. Keep batteries out of reach of children. If you think batteries may have
been swallowed or placed inside any part of the body, seek immediate medical
attention.

APEX™, HELIX®, Humminbird®, MEGA 360 Imaging™, MEGA Live Imaging™, Minn Kota®,
SOLIX®, TargetLock™, Ultrex™ are trademarked by or registered trademarks of Johnson
Outdoors Marine Electronics, Inc.

© 2022 Johnson Outdoors Marine Electronics, Inc. All rights reserved.

«
1
2
3
4
5
...
»

Summary of Contents for MEGA Live












































































Reviews:

No comments

Related manuals for MEGA Live

Brand: 4iiii Pages: 36

Brand: 4iiii Pages: 34

Brand: 4EVAC Pages: 27

Brand: ParaBody Pages: 5

Brand: National Instruments Pages: 10

QUICK-ALIGN Vari-Flex

Brand: Össur Pages: 36

Brand: Össur Pages: 2

Brand: Össur Pages: 8

Brand: LSI Pages: 24

Brand: Nady Audio Pages: 2

Fresh DFG58D1BSS

Brand: Danby Pages: 11

PRO-FORM ab GLIDER

Brand: ICON Health & Fitness Pages: 16

Aesculap S4 Cervical

Brand: B. Braun Pages: 43

Dynamique Biski

Brand: Enabling Technologies Pages: 44

Brand: Blizzard Lighting Pages: 24

Brand: Sima Pages: 22

Brand: Laserscope Pages: 74

Brand: Esaote Pages: 138

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands