Humminbird MEGA Live Manual Download | Manualshive

Page: 17 / 75

background image

11

MEGA Live Installation

B. MEGA Live Dual Mounting Plate

(for MEGA Live and MEGA 360 installation)

The dual mounting plate (separate purchase) will allow you to install your MEGA
Live Imaging TargetLock on one side of your trolling motor and your MEGA 360 on
the other.

1. If you have a trolling motor stabilizer installed, you will first need to uninstall

it. You will reinstall it after you have completed installation of your MEGA Live.
See the installation guide that was included with your trolling motor or visit

www.minnkotamotors.com

for instructions.

2. Align the plate below the BowGuard. Line up the holes on the plate with the

threaded holes on the BowGuard.

3. Install the six (6) included 5/16-18 x 1" bolts through the plate and into the

BowGuard. Hand-tighten using a 9/16 nut driver until secure (see the illustration

Installing the Mounting Plate

). Hand-tighten only!

Installing the Dual Mounting Plate

«
...
15
16
17
18
19
...
»

Summary of Contents for MEGA Live












































































Reviews:

No comments

Related manuals for MEGA Live

Brand: NARGESA Pages: 50

Brand: DAKO Pages: 25

Brand: 3M ESPE Pages: 50

Brand: VACGEN Pages: 13

Brand: PANDROL Pages: 36

BODY ARMOR PRO TERM

Brand: Darco Pages: 6

Brand: V-TAC Pages: 13

Brand: Gardena Pages: 33

Brand: A.HABERKORN Pages: 28

Brand: Rowlinson Garden Products Pages: 5

Brand: York International Pages: 16

Brand: X-10 Pages: 12

Brand: Equinox Systems Pages: 8

Brand: Poulan Pro Pages: 17

ANY SPOT AS-1400-2P

Brand: Galaxy Audio Pages: 12

Brand: Knightsbridge Pages: 4

Brand: Pepperl+Fuchs Pages: 2

Brand: Studiomaster Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands