Humminbird MEGA Live Manual Download | Manualshive

Page: 29 / 75

background image

23

MEGA Live Installation

10. Reinstall the Motor Stabilizer

1. If you removed your motor stabilizer prior to installing your Mega Live, reinstall

it now through the MEGA Live plate (see the illustration

Reinstalling the

Motor Stabilizer

) using the provided 5/16" screws with locking washers. It

may be necessary to shorten your motor stabilizer. See the installation guide
that was included with your trolling motor or visit

www.minnkotamotors.com

for more information.

NOTE:

A trolling motor stabilizer (included with each Minn Kota Ultrex trolling

motor or available as a separately purchased accessory) is required to support your
MEGA Live Targetlock. It

must

be installed before taking your MEGA Live on the

water.

Reinstalling the Motor Stabilizer

«
...
27
28
29
30
31
...
»

Summary of Contents for MEGA Live












































































Reviews:

No comments

Related manuals for MEGA Live

Brand: Rangevision Pages: 28

Brand: Hacker Pages: 2

Brand: J.P. SELECTA Pages: 8

Brand: Haemonetics Pages: 134

Brand: Hadeco Pages: 72

Brand: Nellcor Pages: 161

OXIMAX N-600X Series

Brand: Nellcor Pages: 210

Brand: Oase Pages: 120

Brand: OAKWORKS Pages: 24

Brand: Rane Pages: 6

Brand: Rane Pages: 27

Brand: Ranger Products Pages: 6

Brand: Rane Pages: 88

Brand: Haag-Streit Pages: 21

Brand: MAGSTIM Pages: 86

AP4600 MK3 Series

Brand: Oxylitre Pages: 15

Brand: Bad Caf Pages: 2

Circaid Juxtafit Essentials

Brand: medi Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands