Humminbird MEGA Live Manual Download

Page: 15 / 75

MEGA Live Installation

4. Determine if you must uninstall and reinstall your trolling motor stabilizer. You will

need to uninstall and reinstall the stabilizer if:

• You are installing your MEGA Live on the starboard side of your trolling motor.

• You are installing the dual mount accessory (for MEGA Live and MEGA 360

installation, separate purchase required).

You will reinstall the stabilizer after you have completed installation of your MEGA
Live. See the installation guide that was included with your trolling motor or visit

www.minnkotamotors.com

for installation instructions.

NOTE:

A trolling motor stabilizer included with each Minn Kota Ultrex trolling motor

or available as a separately purchased accessory) is required to support your MEGA
Live Targetlock. It

must

be installed before taking your MEGA Live on the water.

5. With the trolling motor deployed, the transducer has the following installation

requirements:

• The transducer should not have anything obstructing the ‘view’ of the beams.

If possible, move anything to the sides and below the transducer that might
obstruct the sight line of the beams.

3. Install the Mounting Plate

Proceed to the installation section for the type of mounting plate you will be using:

A. MEGA Live Mounting Plate (for use with MEGA Live Imaging TargetLock only)

B. MEGA Live Dual Mounting Plate (for use with MEGA Live Imaging TargetLock

and MEGA 360, separate purchase required)

Summary of Contents for MEGA Live












































































Search results

Summary of Contents for MEGA Live

Reviews:

Related manuals for MEGA Live

Brands by name

Popular brands

Humminbird MEGA Live, Manual

Search results

Summary of Contents for MEGA Live

Reviews:

Related manuals for MEGA Live

Brands by name

Popular brands