Humminbird MEGA Live Manual Download | Manualshive

Page: 16 / 75

background image

10

MEGA Live Installation

A. MEGA Live Mounting Plate

(for MEGA Live installation only)

The plate can be mounted on the left or right side of the trolling motor. If you have a
motor stabilizer already installed on one side of the motor, install the mounting plate
on the opposite side.

1. Align the plate below the BowGuard. Line up the holes on the plate with the

threaded holes on the BowGuard.

2. Install the four (4) included 5/16-18 x 1" bolts through the plate and into the

BowGuard. Hand-tighten using a 5/16 nut driver until secure (see the illustration

Installing the Mounting Plate

). Hand-tighten only!

Installing the Mounting Plate

«
...
14
15
16
17
18
...
»

Summary of Contents for MEGA Live












































































Reviews:

No comments

Related manuals for MEGA Live

Brand: GE Pages: 138

Brand: Hacker Pages: 2

Brand: J.P. SELECTA Pages: 8

Brand: Haemonetics Pages: 134

Brand: Hadeco Pages: 72

Brand: Vatech Pages: 137

Brand: Vatech Pages: 68

Brand: Varytec Pages: 52

Brand: B medical systems Pages: 28

Brand: Garmin Pages: 41

Brand: BRAND Pages: 21

Brand: Milestone Pages: 40

Firefly 808 Universal

Brand: Phonic Pages: 27

Brand: Jandy Pages: 52

Brand: Pixlip Pages: 15

Brand: Glow Bricks Pages: 9

Brand: KYORITSU Pages: 16

Brand: Samson Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands