Humminbird MEGA Live Manual Download

Page: 64 / 75

Control Head Setup

Adjust (G3N):

To adjust the zero point of the GPS Heading Sensor, select Main

Menu > Navigation tab > Heading Offset. Press the RIGHT or LEFT Cursor keys
to adjust the setting.

Adjust (G4N):

To adjust the zero point of the GPS Heading Sensor, select Main

Menu > Data Sources tab > Data Offsets> Heading Adjustment. Press the
RIGHT or LEFT Cursor keys to adjust the setting.

If the procedure failed:

If the Heading digital readout is significantly different

than the COG, the GPS Heading Sensor might be installed in a location with
too much magnetic interference. Check the installation location and possible
magnetic disturbances in the area.

Confirming the Heading Digital Readout (HELIX)

heading

(heading

sensor

required)

course

Summary of Contents for MEGA Live












































































Search results

Summary of Contents for MEGA Live

Reviews:

Related manuals for MEGA Live

Brands by name

Popular brands

Humminbird MEGA Live, Manual

Search results

Summary of Contents for MEGA Live

Reviews:

Related manuals for MEGA Live

Brands by name

Popular brands