Hughes HN9200 Installation Manual Download Page 95

Page: 95 / 132

Chapter

Troubleshooting

This chapter provides troubleshooting procedures. Most section headings describe
a problem you could encounter (such as

System LED is off

) or they describe

Topics:

•

Important troubleshooting
information

troubleshooting procedures for correcting a problem (such as

Confirming

Internet connectivity

). To correct a problem, find the description that matches

your problem, then find the troubleshooting procedure or procedures for your
problem.

•

Troubleshooting reference
diagram

•

Troubleshooting common
problems

If you cannot correct the problem, contact Hughes Installer Support.

Other sections in this guide that contain troubleshooting information are listed
below:

•

Cannot access the Internet

•

Cannot access the System
Control Center

• For explanation of

red flags

on System Control Center screens, see

Red

flag indicator

on page 68.

•

Using the front panel LEDs for
troubleshooting

• The

Advanced Pages

contain diagnostic and other information that may

help in troubleshooting. See

Advanced Pages

on page 103.

•

Problem with a connected device

•

Using the LAN port LEDs for
troubleshooting

In addition, the HN9200 satellite modem provides its own online Help, which
includes substantial troubleshooting information (including troubleshooting
commissioning problems). Access this information through the System Control
Center

Help

link (

Help

→

Frequently Asked Questions

•

Troubleshooting other problems

•

Viewing problem-related statistics

Another valuable source of troubleshooting information is the HughesNet
Knowledge Base, available online at

http://kb.hughesnet.com

•

Checking for possible AC outlet
problems

HN9200 Satellite Modem Installation Guide

1038622-0001 Revision B

Summary of Contents for HN9200





































































































































Search results

Summary of Contents for HN9200

Reviews:

Related manuals for HN9200

Brands by name

Popular brands

Hughes HN9200, Installation Manual

Search results

Summary of Contents for HN9200

Reviews:

Related manuals for HN9200

Brands by name

Popular brands