Hughes HN9200 Installation Manual Download Page 18

Page: 18 / 132

to have an electrician evaluate the electrical power outlet. N-G voltages may have a negative
impact on the performance of electronic equipment.

Grounding (modem, antenna, radio, and IFL)

Adhere to Hughes grounding requirements.

Use only approved ground wires, ground blocks, lugs, and clamps.

For detailed information refer to the appropriate FSB, as listed in

Table 3: Related installation

documents

on page 11.

Items required for installation

To install the HN9200 satellite modem, you need:

• HN9200 satellite modem

• Power supply (provided in the shipping carton)

• Surge protector (recommended), provided by the customer
• Cat-5 Ethernet cable

•

sbc.cfg

file (if you are instructed to upload it)

• Installation Reference Sheet (provided to the installer)

•

Welcome to HughesNet

quick start guide (1038043-0001) (to give to the customer)

Notes

sbc.cfg file

– If needed, you can download the most current

sbc.cfg

file from your installation

support web site.

SAN and PIN

– Identification numbers are required to register the satellite modem. Customers

who purchased their system from a Hughes retail channel in the United States or Canada receive
an order confirmation e-mail containing their site account number (SAN) and personal
identification number (PIN).

DC/DC power supply

– If the site has a DC power source, it requires a DC/DC power supply.

See

Table 2: Power supply specifications for the HN9200 satellite modem

on page 8. The

installer must provide the wire required to assemble the DC input power cable.

Additional equipment

• Antenna
• Hughes antenna pointing tool (DAPT for Ka-band, DAPT or OPI for Ku-band)
• IFL cables, cable connectors, and ground blocks

For more information on these items, see

Related components

on page 9.

No tools are required to install the modem. For tools needed to install the antenna mount and
antenna and point the antenna, see:

•

Antenna Site Preparation and Mount Installation Guide

(1035678-0001)

• The installation guide for the antenna model you are installing

HN9200 Satellite Modem Installation Guide

1038622-0001 Revision B

Preparing for installation

Chapter 2

Summary of Contents for HN9200





































































































































Search results

Summary of Contents for HN9200

Reviews:

Related manuals for HN9200

Brands by name

Popular brands

Hughes HN9200, Installation Manual

Search results

Summary of Contents for HN9200

Reviews:

Related manuals for HN9200

Brands by name

Popular brands