Hughes HN9200 Installation Manual Download Page 3

Page: 3 / 132

Contents

Understanding safety alert messages.................................................................................xi

Messages concerning personal injury.....................................................................................................xi

Messages concerning property damage...................................................................................................xi

Safety symbols........................................................................................................................................xi

Chapter 1: Satellite modem overview............................................................1

Scope of this installation guide................................................................................................................2

Satellite modem specifications.................................................................................................................2

Chapter 2: Preparing for installation.............................................................3

Installation summary................................................................................................................................4

Installation checklist.................................................................................................................................5

Items required for installation..................................................................................................................6

Conducting a site survey..........................................................................................................................7

Power supply information........................................................................................................................7

Computer and networking requirements..................................................................................................8

Computer requirements................................................................................................................8

Networking and Internet browser requirements...........................................................................9

Related components.................................................................................................................................9

Antenna........................................................................................................................................9

IFL cables...................................................................................................................................10

Requirements for cables, connectors, and ground blocks..............................................10

Labeling the IFL cables..................................................................................................10

Hub or similar network device...................................................................................................10

Instructions for related components...........................................................................................11

Chapter 3: Installing the satellite modem....................................................13

Prerequisites for installing the modem...................................................................................................14

Selecting the modem installation location..............................................................................................14

Ventilation and heat sources.......................................................................................................14

Modem operating position.....................................................................................................................14

Connecting the transmit and receive cables...........................................................................................15

Connecting the installer laptop to the modem........................................................................................16

Connecting the power supply.................................................................................................................17

Connecting an AC/DC power supply.........................................................................................17

Connecting and assembling a DC/DC power supply.................................................................18

Powering up the modem.........................................................................................................................19

AC/DC power supply.................................................................................................................19

DC/DC power supply.................................................................................................................19

iii

HN9200 Satellite Modem Installation Guide

1038622-0001 Revision B

Summary of Contents for HN9200





































































































































Search results

Summary of Contents for HN9200

Reviews:

Related manuals for HN9200

Brands by name

Popular brands

Hughes HN9200, Installation Manual

Search results

Summary of Contents for HN9200

Reviews:

Related manuals for HN9200

Brands by name

Popular brands