Hughes HN9200 Installation Manual Download Page 36

Page: 36 / 132

Do not power cycle the satellite modem by

unplugging the power cord from the modem’s rear panel. Doing so could result in static
electricity discharge that could shock you and/or damage the modem.

Make sure an Ethernet router or switch is not connected to the satellite modem and to the
customer’s computer.

Try the ping test again.

If the ping test is unsuccessful, call Installer Support for assistance.

Uploading the sbc.cfg file to the satellite modem

The

sbc.cfg

file contains satellite information for SBC and the auto-commissioning server (ACS)

to be used for the commissioning process. Once you have obtained the

sbc.cfg

file, save it on

the installer laptop computer making sure to note the location where the file is saved.

If you do not need to upload an

sbc.cfg

file, go to

Entering the antenna location

on page 27.

To upload the

sbc.cfg

file:

Open a browser on the installer laptop.

Type

http://192.168.0.1/fs/registration/setup.html

in the address bar.

Press

Enter

The Satellite Setup menu appears.

HN9200 Satellite Modem Installation Guide

1038622-0001 Revision B

Commissioning the satellite modem

Chapter 4

Summary of Contents for HN9200





































































































































Search results

Summary of Contents for HN9200

Reviews:

Related manuals for HN9200

Brands by name

Popular brands

Hughes HN9200, Installation Manual

Search results

Summary of Contents for HN9200

Reviews:

Related manuals for HN9200

Brands by name

Popular brands