Hughes HN9200 Installation Manual Download Page 16 | Manualshive

Page: 16 / 132

background image

Installation summary

This guide explains how to install the HN9200 satellite modem. It includes

limited

information

about other satellite terminal components. The

satellite modem

is the small indoor unit. The

satellite terminal

includes the satellite modem and the antenna, radio assembly, and IFL cables,

as shown in

Figure 2: Satellite modem and related terminal components

on page 4.

Figure 2: Satellite modem and related terminal components

This summary focuses on installation of the satellite modem, but also includes some information
on related tasks such as antenna installation and pointing. The tasks listed below are the main
installation tasks,

but these are not all

of the installation tasks.

Complete all steps in the order they are presented in this installation guide unless you have a
specific reason for doing them in a different order. In any case, make sure all steps are completed.
You must install the antenna before the satellite modem can be commissioned. Then you point
the antenna as part of the modem commissioning procedure.

Details for the satellite modem installation tasks are included in later chapters in this guide.

Preparing for the installation

• Make sure you have all items required for installation, including the Installation Reference

Sheet, all equipment to be installed, and required tools for the outdoor equipment.

• Make sure the customer's computer meets the requirements listed in

Computer and networking

requirements

on page 8.

• Conduct a site survey.
• Assemble and install the antenna and radio as instructed in the antenna installation guide.

Installing the satellite modem

• Connect the transmit and receive cables.
• Connect the modem to the installer laptop.
• Connect the power supply.
• Power up the modem and observe the LEDs to verify normal operation.

Commissioning the modem and pointing the antenna

• Upload the

sbc.cfg

file (if you are instructed to upload it).

HN9200 Satellite Modem Installation Guide

4

1038622-0001 Revision B

Preparing for installation

Chapter 2

«
...
14
15
16
17
18
...
»

Summary of Contents for HN9200





































































































































Reviews:

No comments

Related manuals for HN9200

Brand: Patton electronics Pages: 9

Alpha GMT 125 Series

Brand: EnerSys Pages: 26

Brand: Aeotec Pages: 6

Brand: BandLuxe Pages: 22

MultiModem MTCBA?EV1?U1?N3

Brand: Multitech Pages: 24

Brand: FW Pages: 12

Brand: Motorola Pages: 12

Brand: ELTEX Pages: 6

Brand: Nokia Pages: 10

Plus TV PVR-TV 305U

Brand: KWorld Pages: 9

MOBIIBROADBAND 4G

Brand: iiNet Pages: 2

Brand: iiNet Pages: 55

Brand: Zte Pages: 12

Brand: Primus Pages: 2

Brand: Enfora Pages: 28

Brand: Enfora Pages: 27

Skywire LTE NL-SW-LTE-S7 Series

Brand: NimbeLink Pages: 16

Brand: SmartRG Pages: 117

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands