Hughes HN9200 Installation Manual Download Page 30

Page: 30 / 132

Figure 7: Connecting an AC power supply

Connecting and assembling a DC/DC power supply

Figure 8: DC/DC power supply

on page 18 shows the DC/DC power supply used with the

HN9200 modem.

Figure 8: DC/DC power supply

Connect and assemble the DC/DC power supply as follows:

Connect the DC power cord to the DC IN port on the modem.

Note:

The input cable kit is included in the power supply kit. The cable kit contains

an input power connector, connector pins, and a wiring diagram; it does not include
wire.

Assemble the input power cable according to the wiring diagram included in the cable kit.

HN9200 Satellite Modem Installation Guide

1038622-0001 Revision B

Installing the satellite modem

Chapter 3

Summary of Contents for HN9200





































































































































Search results

Summary of Contents for HN9200

Reviews:

Related manuals for HN9200

Brands by name

Popular brands

Hughes HN9200, Installation Manual

Search results

Summary of Contents for HN9200

Reviews:

Related manuals for HN9200

Brands by name

Popular brands