Hughes HN9200 Installation Manual Download Page 27

Page: 27 / 132

Figure 4: HN9200 in vertical position

Connecting the transmit and receive cables

Connect the transmit and receive IFL cables to the satellite modem.

Connect the transmit and receive cables to the connectors on the rear panel of the modem as
shown in

Figure 5: Connecting the transmit and receive cables to the modem

on page 15.

Figure 5: Connecting the transmit and receive cables to the modem

The transmit and receive cable connectors must be securely

tightened.

• Make sure each connector is properly aligned (not cross-threaded).
• The connector should be finger tight with no play.

HN9200 Satellite Modem Installation Guide

1038622-0001 Revision B

Chapter 3

Installing the satellite modem

Summary of Contents for HN9200





































































































































Search results

Summary of Contents for HN9200

Reviews:

Related manuals for HN9200

Brands by name

Popular brands

Hughes HN9200, Installation Manual

Search results

Summary of Contents for HN9200

Reviews:

Related manuals for HN9200

Brands by name

Popular brands