Hughes HN9200 Installation Manual Download Page 87

Page: 87 / 132

Figure 64: System Information page

The parameters listed in the

HN9200 Info

section of the System Information page are explained

in the following table. Other sections of the screen (

Transmit Radio Info

and

Satellite

) provide

additional information about the modem installation and the modem software (

Software

Configuration

Table 9: System Information page parameters – HN9200 Info section

Explanation

Parameter

Identifies the site where the modem is installed.

Site ID

The modem’s serial number. The serial number may be required
for troubleshooting.

Serial number

ZIP code of the modem site.

Zipcode

Software build date.

Software Date

Version of the modem’s software. This is typically the
factory-installed software version. However, if the NOC downloads

Software Release

a newer version of Gateway software to the modem, the newer
version number is displayed.

The satellite modem address. The default modem address is
192.168.0.1. A different modem address can be configured.

LAN1 IP Address

Range of addresses available to the satellite modem.

LAN1 Subnet Mask

MAC address for the satellite modem.

LAN1 MAC Address

HN9200 Satellite Modem Installation Guide

1038622-0001 Revision B

Chapter 6

System Control Center

Summary of Contents for HN9200





































































































































Search results

Summary of Contents for HN9200

Reviews:

Related manuals for HN9200

Brands by name

Popular brands

Hughes HN9200, Installation Manual

Search results

Summary of Contents for HN9200

Reviews:

Related manuals for HN9200

Brands by name

Popular brands