Hughes HN9200 Installation Manual Download Page 33 | Manualshive

Page: 33 / 132

background image

Chapter

4

Commissioning the satellite modem

Commissioning refers to a series of procedures to make the newly installed
satellite modem ready for network operation and register the modem with the
service provider’s network.

Topics:

•

Satellite-based commissioning

•

Manual commissioning

Commissioning methods

Two methods are available for commissioning the HN9200 satellite modem:

•

Satellite-based commissioning

on page 22

•

Manual commissioning

on page 50

Satellite-based commissioning is the preferred commissioning method. Use the
manual commissioning method only if satellite-based commissioning is not
available

and

if you are instructed to do so by the service provider.

21

HN9200 Satellite Modem Installation Guide

1038622-0001 Revision B

«
...
31
32
33
34
35
...
»

Summary of Contents for HN9200





































































































































Reviews:

No comments

Related manuals for HN9200

Brand: MailASail Pages: 2

Brand: CS Pages: 50

Brand: Patton electronics Pages: 8

Brand: Ovation Pages: 9

Brand: FW Pages: 12

Brand: Motorola Pages: 14

Brand: Motorola Pages: 58

Brand: Motorola Pages: 66

Brand: Motorola Pages: 123

Brand: Motorola Pages: 12

Brand: Motorola Pages: 16

Brand: Motorola Pages: 8

Brand: Motorola Pages: 12

Brand: Motorola Pages: 2

Brand: Motorola Pages: 188

Brand: Motorola Pages: 117

Brand: Motorola Pages: 240

Brand: Motorola Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands