Hughes HN9200 Installation Manual Download Page 31

Page: 31 / 132

Connect the input power cable to the DC power source, but do not connect the input power
connector to the power supply at this time.

Do not connect the input power connector to the power supply until you are ready to observe
the modem’s LEDs upon power-up, as explained in

LEDS on power-up

on page 19.

Powering up the modem

Check

Power supply information

on page 7 to make sure you have the correct power supply.

Follow these instructions to power up the modem for the first time.

AC/DC power supply

Prerequisites:

• The power outlet has been tested, as described in

Connecting an AC/DC power supply

page 17.

• According to previous instructions, the DC power cord is connected to the modem’s rear

panel, and the AC power cord is connected to the power supply.

Connect the AC power cord into the surge protector or wall outlet.

Observe the LEDs for proper operation. See

LEDS on power-up

on page 19.

DC/DC power supply

Prerequisites: The DC power cord is connected to the modem’s rear panel, and the input power
cable is assembled and connected to the DC power source.

Connect the input cable connector to the power supply.

Observe the LEDs for proper operation. See

LEDS on power-up

on page 19.

LEDS on power-up

As the modem powers up, observe the front panel LEDs to make sure the modem is working
properly. When power is applied to the modem or after a modem reset, the LEDs light up in the
following order, indicating normal power-up:

All LEDs light up for ½ sec while the modem performs a self-test.

The Power LED lights up and remains on, indicating the modem is powered up.

The Power LED and System LED light up for about 5 to 10 sec while the modem loads and
prepares applications.

If the modem LAN port is connected to a network device, the LAN LED lights up within 30
sec, indicating that LAN connectivity is detected.

The Power LED blinks, indicating that the modem is not commissioned.

If the LEDs do not function as described, make sure you have the correct power supply. Refer
to

Table 2: Power supply specifications for the HN9200 satellite modem

on page 8.

HN9200 Satellite Modem Installation Guide

1038622-0001 Revision B

Chapter 3

Installing the satellite modem

Summary of Contents for HN9200





































































































































Search results

Summary of Contents for HN9200

Reviews:

Related manuals for HN9200

Brands by name

Popular brands

Hughes HN9200, Installation Manual

Search results

Summary of Contents for HN9200

Reviews:

Related manuals for HN9200

Brands by name

Popular brands