Hubbell GARD Pro Instruction Manual Download Page 93

Page: 93 / 345

System Configuration __________________________________________________________________

RF-MCGARDPRO

Hubbell Power Systems, Inc.

–

RFL™

Products

July 1, 2022

4-18

4.7

Dynamic Menu Feature

Certain items on the sidebar menu are dynamic in nature as shown below. Clicking the listing
with the “

” next to it in this example will reveal the type of PLC modules installed in the

HPS/RFL GARD Pro system with their slot location. You can then select the module to be
configured.

Note:

The module description will also appear in a dropdown menu at the top of the web page.

Clicking the listing with the “

” symbol will

reveal the type of PLC modules installed in

the GARD Pro along with their slot location

Then select the

module to be

configured

Figure 4-17. Dynamic Menu Feature

Summary of Contents for GARD Pro


























































































































































































































































































































































Search results

Summary of Contents for GARD Pro

Reviews:

Related manuals for GARD Pro

Brands by name

Popular brands

Hubbell GARD Pro, Instruction Manual

Search results

Summary of Contents for GARD Pro

Reviews:

Related manuals for GARD Pro

Brands by name

Popular brands