Hubbell GARD Pro Instruction Manual Download Page 249

Page: 249 / 345

Digital Teleprotection __________________________________________________________________

RF-MCGARDPRO

Hubbell Power Systems, Inc.

–

RFL™

Products

July 1, 2022

6-16

Digital Teleprotection Timeslot configuration example

The Bus Master is the RS449 in
slot 1 and the timing is internal.

Timeslots can be marked Idle

C37.94 Function is
assigned to Timeslot 4.
Green indicates the need
to save the changes

Timeslots 1-3 were
selected for RS449.

Interfaces must occupy only
continuous timeslots so the middle
Interface is unavailable for editing.

Figure 6-11. Digital Teleprotection Configuration Example

Note

: The “Idle” timeslots do not require a comms Interface. If Idle is assigned to a comms

interface it will increase the interface data rate accordingly.

Note

: The “Bus Master” field is active when there is more than one interface programmed on the

Bus.

Summary of Contents for GARD Pro


























































































































































































































































































































































Search results

Summary of Contents for GARD Pro

Reviews:

Related manuals for GARD Pro

Brands by name

Popular brands

Hubbell GARD Pro, Instruction Manual

Search results

Summary of Contents for GARD Pro

Reviews:

Related manuals for GARD Pro

Brands by name

Popular brands