Hubbell GARD Pro Instruction Manual Download Page 189

Page: 189 / 345

Power Line Carrier ____________________________________________________________________

RF-MCGARDPRO

Hubbell Power Systems, Inc.

–

RFL™

Products

July 1, 2022

5-34

Current Force Carrier State:

Once the carrier state has been changed and the command

sent and verified, the change in state will be displayed here.

These status indicators (which are fixed) are derived from the On/Off configuration web
page and displayed here for reference.

Frequency:

Displays the current settings.

Send

: In 'Master' mode, starts the checkback test. In 'Remote' mode, send the remote-

initiate code. If 'Disabled’, this button is also disabled.

Send Checkback Code:

Sends the selected checkback code to the far end as follows:

1-16 or none. Click the “Send” button. A confirmation window will appear, click “Send
Command.”

Click to send the Remote Initiate code to the Master end.

Send Hard Carrier:

Sends the selected hard carrier request to the far end. The selections

are 1 to 4 or none. Once selected click “Send.”

PLC Module Logic Bus Outputs:

Enables or disables the Logic Bus Outputs. Once a

change is made click the “Activate” button to change the Logic Bus Output state.

5.4.3 Receiver Operating Range and Dynamic Range

RX AGC Setpoint

setting Sets headroom in

the analog portion of receiver. Set to 30 dB

Nominal Trip Level (Boost)

Nominal Guard Level

Maximum receiver sensitivity 25 Vrms

Signal Dropout Alarm

(FSK only)

Min RX Level

Setting On/Off = -15dB/FSK = -11dB

For On/Off determines max inst. drop from nominal to block

For FSK determines max inst. drop from nominal to trip

+30 dB

+10 dB

0 dB

Maximum receiver sensitivity 5 mVrms

-10 dB

-11 dB

-25 dB

Dynamic
Range

FSK Trip RX Threshold

(FSK Only) Absolute minimum

level required to trip. Recommended setting 25 dB

(Range 0 dB to 100 dB)

Receiver
Operating
Range

SNR Alarm Threshold

(FSK Only) Issues an alarm, and disables tripping for noise levels exceeding the ratio setting.

Recommended setting 10 dB (0 dB to 30 dB range)

Figure 5-17. Receiver Operating Range and Dynamic Range

Summary of Contents for GARD Pro


























































































































































































































































































































































Search results

Summary of Contents for GARD Pro

Reviews:

Related manuals for GARD Pro

Brands by name

Popular brands

Hubbell GARD Pro, Instruction Manual

Search results

Summary of Contents for GARD Pro

Reviews:

Related manuals for GARD Pro

Brands by name

Popular brands