Huawei FusionServer Pro 2288H V5 User Manual Download

Page: 37 / 177

Configuration Maximum

Front Drives

Maximum
Rear Drives

Maximum
Built-in
Drives

Drive
Management
Mode

12 x 3.5" drive
pass-through
configuration 2

Slots 0 to 11
support only
SATA
drives.

I/O module
3: 4

–

Slots 44
to 47
support
only
NVMe
drives.

PCH

12 x 3.5" drive
pass-through
configuration 3

Slots 0 to 11
support only
SAS/SATA
drives.

I/O module
3: 4

–

Slots 44
to 47
support
only
NVMe
drives.

Slots 36 to
39 support
only SAS/
SATA
drives.

2 x RAID
controller card

20 x 2.5" (8 x
SAS/SATA
+ 12 x NVMe)
drive
configuration

Slots 0 to 7
support only
SAS/SATA
drives.

Slots 8 to 19
support only
NVMe
drives.

I/O module
3: 4

–

Slots 44
to 47
support
only
NVMe
drives.

1 x RAID
controller
card/PCH

24 x 2.5" drive
pass-through
configuration

Slots 0 to 23
support only
SAS/SATA
drives.

I/O module
3: 4

–

Slots 44
to 47
support
only
NVMe
drives.

3 x RAID
controller card

24 x 2.5"
NVMe
configuration

Slots 0 to 3
support
SAS/SATA/
NVMe
drives.

Slots 4 to 23
support only
NVMe
drives.

I/O module
3: 4

–

Slots 44
to 47
support
only
NVMe
drives.

1 x RAID
controller card

FusionServer Pro 2288H V5 Server
User Guide

2 Hardware Description

Issue 08 (2019-10-30)

Summary of Contents for FusionServer Pro 2288H V5


















































































































































































Search results

Summary of Contents for FusionServer Pro 2288H V5

Reviews:

Related manuals for FusionServer Pro 2288H V5

Brands by name

Popular brands

Huawei FusionServer Pro 2288H V5, User Manual

Search results

Summary of Contents for FusionServer Pro 2288H V5

Reviews:

Related manuals for FusionServer Pro 2288H V5

Brands by name

Popular brands