Huawei FusionServer Pro 2288H V5 User Manual Download

Page: 48 / 177

Port Type

Indicator

Description

Connection status
indicator

Off: The network port is not connected.

Steady green: The network port is
properly connected.

10GE electrical port

Transmission rate
indicator

Off: The data transmission rate is 10/100
Mbit/s.

Steady green: The data transmission rate
is 10 Gbit/s.

Steady yellow: The data transmission
rate is 1 Gbit/s.

Connection status
indicator/Data
transmission status
indicator

Off: No data is being transmitted or the
network port is not connected.

Blinking green: Data is being
transmitted.

Steady green: The network port is
properly connected.

25GE optical port

Transmission rate
indicator

Off: The network port is not connected.

Steady green: The data transmission rate
is 25 Gbit/s.

Steady yellow: The data transmission
rate is 10 Gbit/s.

Connection status
indicator/Data
transmission status
indicator

Off: The network port is not connected.

Blinking green: Data is being
transmitted.

Steady green: The network port is
properly connected.

56G IB optical port

Connection status
indicator

Off: No physical link is set up.

Blinking green: The physical link is
abnormal.

Steady green: The physical link is
normal.

Data transmission
status indicator

Off: No logical link is set up.

Blinking yellow: Data is being
transmitted.

Steady yellow: The logical link is
normal but no data is being transmitted.

2.7 I/O Expansion

FusionServer Pro 2288H V5 Server
User Guide

2 Hardware Description

Issue 08 (2019-10-30)

Summary of Contents for FusionServer Pro 2288H V5


















































































































































































Search results

Summary of Contents for FusionServer Pro 2288H V5

Reviews:

Related manuals for FusionServer Pro 2288H V5

Brands by name

Popular brands

Huawei FusionServer Pro 2288H V5, User Manual

Search results

Summary of Contents for FusionServer Pro 2288H V5

Reviews:

Related manuals for FusionServer Pro 2288H V5

Brands by name

Popular brands