Huawei FusionServer Pro 2288H V5 User Manual Download

Page: 18 / 177

Indicator and Button Description

Table 2-1

Indicators and buttons on the front panel

Silkscreen

Indicator/
Button

Description

Fault diagnosis
LED

---: The device is operating normally.

Fault code: A component is faulty.
For details about error codes, see

FusionServer

Pro Rack Server iBMC Alarm Handling

Power button/
indicator

Power indicator:

Off: The device is not powered on.

Steady yellow: The device is powered on.

Blinking yellow: The power button is locked. The
power button is locked when the iBMC is starting.

Steady green: The device is ready to power on.

Power button:

When the device is powered on, you can press this
button to gracefully shut down the OS.

When the device is powered on, holding down this
button for 6 seconds will forcibly power off the
device.

When the power indicator is steady green, you can
press this button to power on the device.

UID button/
indicator

The UID button/indicator helps identify and locate a
device.
UID indicator:

Off: The device is not being located.

Blinking blue: The device has been located and is
differentiated from other devices that have also
been located.

Steady blue: The device is being located.

UID button:

You can turn on or off the UID indicator by
pressing the UID button on the panel or by using
the iBMC CLI or WebUI.

You can press this button to turn on or off the UID
indicator.

You can press and hold down this button for 4 to 6
seconds to reset the iBMC.

FusionServer Pro 2288H V5 Server
User Guide

2 Hardware Description

Issue 08 (2019-10-30)

Summary of Contents for FusionServer Pro 2288H V5


















































































































































































Search results

Summary of Contents for FusionServer Pro 2288H V5

Reviews:

Related manuals for FusionServer Pro 2288H V5

Brands by name

Popular brands

Huawei FusionServer Pro 2288H V5, User Manual

Search results

Summary of Contents for FusionServer Pro 2288H V5

Reviews:

Related manuals for FusionServer Pro 2288H V5

Brands by name

Popular brands