Huawei FusionServer Pro 2288H V5 User Manual Download Page 119 | Manualshive

Page: 119 / 177

background image

l

The default boot mode is UEFI.

l

For some OSs, if the capacity of the drive or RAID array for installing the OS is greater than 2 TB,
use the UEFI boot mode. For details, see the release notes of the OS.

l

If the OS is installed on an NVMe drive, the boot mode must be the UEFI boot.

l

The UEFI boot mode supports more boot devices than the legacy boot mode. The UEFI boot mode
is recommended if a server is configured with multiple boot devices. If the legacy mode is set, some
devices may fail to boot. If the legacy mode has to be set, disable serial port redirection or NIC PXE
based on service requirements so that the OS can start. For details, see sections "Setting PXE for a
NIC" and "Setting Serial Port Redirection" in

Huawei Server Purley Platform BIOS Parameter

.

Step 4

Select

Boot Sequence

and press

Enter

.

The

Boot Sequence

screen is displayed.

The default boot sequence is

Hard Disk Drive

>

DVD-ROM Drive

>

PXE

>

Others

.

Step 5

Select the target boot device and press

F5

or

F6

to change the boot order.

l

Press

F5

to move a boot option down.

l

Press

F6

to move a boot option up.

The server boots in the order specified on this screen.

----End

7.4.7.3 Setting PXE for a NIC

If a server is configured with multiple NICs, you can set the PXE function for the NICs on the
BIOS.

If multiple boot devices of the same type are configured for a server, you can set the system boot
sequence on the BIOS. For details about how to set the boot device, see

Huawei Server Purley

Platform BIOS Parameter Reference

Procedure

Step 1

On the BIOS main screen, choose

Advanced

.

The

Advanced

screen is displayed.

Step 2

Select

PXE Configuration

and press

Enter

.

The

PXE Configuration

screen is displayed.

l

Four on-board network ports can be displayed on the PXE screen. The default value is

Enabled

for

PXE1 and PXE3 and

Disabled

for other network ports.

l

The I/O NIC ports are also displayed on the

PXE Configuration

screen.

FusionServer Pro 2288H V5 Server
User Guide

7 Installation and Configuration

Issue 08 (2019-10-30)

Copyright © Huawei Technologies Co., Ltd.

111

«
...
117
118
119
120
121
...
»

Summary of Contents for FusionServer Pro 2288H V5


















































































































































































Reviews:

No comments

Related manuals for FusionServer Pro 2288H V5

ShareCenter DNS-343

Brand: D-Link Pages: 12

Brand: LaCie Pages: 4

Brand: Lantronix Pages: 10

Brand: Lantronix Pages: 17

Brand: Lantronix Pages: 109

Brand: Lantronix Pages: 24

Brand: Lantronix Pages: 29

Brand: Lantronix Pages: 2

Brand: Lantronix Pages: 6

Brand: Lantronix Pages: 27

UniServer R6900 G5

Brand: H3C Pages: 17

x3100 M5 Type 5457

Brand: IBM Pages: 688

H SERIES RS/6000

Brand: IBM Pages: 424

Brand: IBM Pages: 220

Brand: ICP DAS USA Pages: 4

Brand: AC&T System Pages: 32

Brand: StarTech.com Pages: 24

PLATINIUM 9000-4R

Brand: MAXDATA Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands