Huawei FusionServer Pro 2288H V5 User Manual Download Page 36

Page: 36 / 177

Configuration Maximum

Front Drives

Maximum
Rear Drives

Maximum
Built-in
Drives

Drive
Management
Mode

12 x 3.5" drive
EXP
configuration 2

Slots 0 to 11
support only
SAS/SATA
drives.

I/O module
1: 2

–

Slots 40
and 41
support
only
SAS/
SATA
drives.

I/O module
3: 4

–

Slots 44
to 47
support
only
NVMe
drives.

2 x RAID
controller card

12 x 3.5" drive
pass-through
configuration 1

Slots 0 to 11
support only
SAS/SATA
drives.

I/O module
1: 2

–

Slots 40
and 41
support
only
SAS/
SATA
drives.

I/O module
2: 2

–

Slots 42
and 43
support
only
SAS/
SATA
drives.

I/O module
3: 4

–

Slots 44
to 47
support
only
NVMe
drives.

1 x RAID
controller card

FusionServer Pro 2288H V5 Server
User Guide

2 Hardware Description

Issue 08 (2019-10-30)

Summary of Contents for FusionServer Pro 2288H V5


















































































































































































Search results

Summary of Contents for FusionServer Pro 2288H V5

Reviews:

Huawei FusionServer Pro 2288H V5, User Manual, Page: 36 / 177

Search results

Summary of Contents for FusionServer Pro 2288H V5

Reviews: