Huawei FusionServer Pro 2288H V5 User Manual Download Page 111

Page: 111 / 177

Step

Description

Upgrade the system.

Upgrade software or firmware, and install or update drivers to
the latest versions.

Documents

Configure the iBMC. The configuration method varies depending on the iBMC version.
For details, see

FusionServer Pro Rack Server iBMC User Guide

Configure RAID settings. For details, see

Huawei V5 Server RAID Controller Card

User Guide

Configure BIOS settings. For details, see

Huawei Server Purley Platform BIOS

Parameter Reference

Install the operating system. For details, see

Huawei Server OS Installation Guide

Handle alarms. For details, see

FusionServer Pro Rack Server iBMC Alarm

Handling

Rectify faults. For details, see

Huawei Servers Troubleshooting

7.4.3 Changing Initial Passwords

7.4.3.1 Changing the Initial Password of the Default iBMC User

Scenarios

This section describes how to change the initial password of the default iBMC user on the
iBMC WebUI.

You can change the initial password of the default iBMC user on:

iBMC WebUI
For details, see

FusionServer Pro Rack Server iBMC User Guide

iBMC CLI
For details, see

FusionServer Pro Rack Server iBMC User Guide

The default user name of the iBMC is

Administrator

, and the default password is

Admin@9000

For security purposes, change the initial password upon the first login and change the password
periodically.

You are advised to use a password that meets complexity requirements or to enable the password
complexity check function.

The password complexity check function is enabled by default.

Procedure

Step 1

For details, see

9.2 Logging In to the iBMC WebUI

FusionServer Pro 2288H V5 Server
User Guide

7 Installation and Configuration

Issue 08 (2019-10-30)

103

Summary of Contents for FusionServer Pro 2288H V5


















































































































































































Search results

Summary of Contents for FusionServer Pro 2288H V5

Reviews:

Related manuals for FusionServer Pro 2288H V5

Brands by name

Popular brands

Huawei FusionServer Pro 2288H V5, User Manual

Search results

Summary of Contents for FusionServer Pro 2288H V5

Reviews:

Related manuals for FusionServer Pro 2288H V5

Brands by name

Popular brands