Huawei FusionServer Pro 2288H V5 User Manual Download

Page: 44 / 177

Green Indicator

Yellow Indicator

Description

Blinking at 1 Hz

The data on the secondary drive is being
rebuilt.

Off

Steady on

A member drive in the RAID array is
removed.

Steady on

The drive is faulty.

NVMe Drive Indicators

Figure 2-34

NVMe drive indicators

If the VMD function is enabled and the latest VMD driver is installed, the NVMe drives
support surprise hot swap.

Table 2-10

NVMe drive indicators (VMD enabled)

Drive Active
Indicator (Green)

Drive Fault
Indicator
(Yellow)

Description

Off

The NVMe drive cannot be detected.

Steady green

Off

The NVMe drive is working properly.

Blinking green at 2
Hz

Off

Data is being read from or written to the
NVMe SSD.

Off

Blinking yellow at
2 Hz

The NVMe drive is being located.

Off

Blinking yellow at
8 Hz

The data on the secondary NVMe drive is
being rebuilt.

Steady green/Off

Steady yellow

The NVMe drive is faulty.

If the VMD function is disabled, NVMe drives support only orderly hot swap.

Table 2-11

NVMe drive indicators (VMD disabled)

Activity
Indicator (Green)

Fault Indicator
(Yellow)

Description

Off

The NVMe drive cannot be detected.

FusionServer Pro 2288H V5 Server
User Guide

2 Hardware Description

Issue 08 (2019-10-30)

Summary of Contents for FusionServer Pro 2288H V5


















































































































































































Search results

Summary of Contents for FusionServer Pro 2288H V5

Reviews:

Related manuals for FusionServer Pro 2288H V5

Brands by name

Popular brands

Huawei FusionServer Pro 2288H V5, User Manual

Search results

Summary of Contents for FusionServer Pro 2288H V5

Reviews:

Related manuals for FusionServer Pro 2288H V5

Brands by name

Popular brands