Huawei FusionServer Pro 2288H V5 User Manual Download

Page: 45 / 177

Activity
Indicator (Green)

Fault Indicator
(Yellow)

Description

Steady green

Off

The NVMe drive is working properly.

Blinking green at 2
Hz

Off

Data is being read from or written to the
NVMe drive.

Off

Blinking yellow at
2 Hz

The NVMe drive is being located or hot-
swapped.

Off

Blinking yellow at
0.5 Hz

The hot removal process is complete, and
the NVMe drive is removable.

Steady green/Off

Steady yellow

The NVMe drive is faulty.

2.5.4 RAID Controller Card

The RAID controller card supports RAID configuration, RAID level migration, and drive
roaming.

Contact your local Huawei sales representative or use the

Intelligent Computing

Compatibility Checker

to determine the RAID controller card to be used.

Table 2-12

RAID levels supported by the 2288H V5

RAID
Level

Reliability

Read
Performan
ce

Write
Performan
ce

Minimum
Number of
Drives

Drive
Utilization

RAID 0

Low

High

100%

RAID 1

High

Low

50%

RAID 5

Relatively
high

High

Medium

–

1)/N

RAID 6

Relatively
high

High

Medium

–

2)/N

RAID 10

High

Medium

50%

RAID 1E

High

Medium

50%

RAID 50

High

Relatively
high

–

M)/N

RAID 60

High

Relatively
high

–

M x

2)/N

M indicates the number of spans in a RAID array.

N indicates the number of member drives in a RAID array.

FusionServer Pro 2288H V5 Server
User Guide

2 Hardware Description

Issue 08 (2019-10-30)

Summary of Contents for FusionServer Pro 2288H V5


















































































































































































Search results

Summary of Contents for FusionServer Pro 2288H V5

Reviews:

Related manuals for FusionServer Pro 2288H V5

Brands by name

Popular brands

Huawei FusionServer Pro 2288H V5, User Manual

Search results

Summary of Contents for FusionServer Pro 2288H V5

Reviews:

Related manuals for FusionServer Pro 2288H V5

Brands by name

Popular brands