Huawei FusionServer Pro 2288H V5 User Manual Download Page 170

Page: 170 / 177

When a single fan is faulty:

The maximum operating temperature is 5°C (41°F) lower than the rated value.

System performance will be affected if GPU cards are configured.

If P4 GPU cards are configured:

The server supports the maximum operating temperature of 35°C (95°F) when holding three or
less GPU cards.

The server supports the maximum operating temperature of 30°C (86°F) when holding four or
more GPU cards.

If V100 GPU cards are configured:

Only the 8 x 2.5" drive configuration is supported.

The maximum operating temperature is 30°C (86°F).

A.5 Nameplate

Certified Model

Usage Restrictions

H22H-05

Global

H22H-05-I10

India only

H22H-05-I12

India only

A.6 RAS Features

The server supports a variety of Reliability, Availability, and Serviceability (RAS) features.
You can configure these features for better RAS.

For details about how to configure RAS features, see

Huawei Server Purley Platform BIOS

Parameter Reference

Table A-3

RAS features

Module

Feature

Description

CPU

Corrected Machine Check
Interrupt

Corrects error-triggered interruption.

DIMM

Failed DIMM Isolation

Identifies a faulty DIMM and isolates it
from others before it is replaced.

Memory Thermal Throttling

Automatically adjusts DIMM temperatures
to avoid damage due to overheating.

Rank Sparing

Allocates some memory ranks as backup
ranks to prevent the system from crashing
due to uncorrectable errors.

FusionServer Pro 2288H V5 Server
User Guide

A Appendix

Issue 08 (2019-10-30)

162

Summary of Contents for FusionServer Pro 2288H V5


















































































































































































Search results

Summary of Contents for FusionServer Pro 2288H V5

Reviews:

Related manuals for FusionServer Pro 2288H V5

Brands by name

Popular brands

Huawei FusionServer Pro 2288H V5, User Manual

Search results

Summary of Contents for FusionServer Pro 2288H V5

Reviews:

Related manuals for FusionServer Pro 2288H V5

Brands by name

Popular brands