HP A7500 Series Command Reference Manual Download Page 149 | Manualshive

Page: 149 / 222

background image

142

issu commit chassis

chassis-number

slot

slot-number

View

System view

Default level

2: System level

Parameters

slot

slot-number

: Specifies the slot number of an MPU that is not upgraded. (In standalone mode)

chassis

chassis-number

: Specifies the member ID of a switch that is not upgraded. (In IRF mode)

chassis

chassis-number

slot

slot-number

: Specifies the location of an MPU that is not upgraded. The

chassis-number

argument is the member ID of the switch where the un-upgraded MPU resides, and

slot-number

is the slot number of the un-upgraded MPU on the switch. (In IRF mode)

Description

1.

In standalone mode

Use the

issu commit

command to upgrade the MPU that is not upgraded.

NOTE:

Execution of the

issu

commit

command is the fourth step in the ISSU upgrade process.

After executing the

issu commit

command, you cannot perform a version rollback operation with the

issu rollback

command.

Related commands:

issu load

and

issu accept

.

2.

In IRF mode

Use the

issu commit chassis

chassis-number

command to upgrade the MPU that is not upgraded. Use this

command when you apply the member switch-based ISSU upgrade method.
Use the

issu commit chassis

chassis-number

slot

slot-number

command to upgrade the MPU that is not

upgraded. Use this command when you apply the MPU-based ISSU upgrade method.

NOTE:

Executing of the

issu

commit

command is the fourth step in the ISSU upgrade process.

Executing of the

issu commit

command completes the ISSU upgrade process, and you cannot perform

a version rollback operation with the

issu rollback

command.

Member switch-based ISSU upgrade method: Upgrade multiple member switches separately to avoid
IRF fabric partition and upgrade failure. In other words, upgrade one member, wait for the switch to

reboot and join the IRF fabric again, and then execute the

issu commit

command to upgrade another

member switch.

MPU-based ISSU upgrade method: Upgrade two MPUs on the same member switch separately, so that
all interfaces cards on the member switch do not reboot.

Related commands:

issu load

and

issu accept

.

Examples

# In the ISSU upgrade process in standalone mode, upgrade the un-upgraded MPU in slot 0 on the

switch.

<Sysname> system-view

«
...
147
148
149
150
151
...
»

Summary of Contents for A7500 Series































































































































































































































Reviews:

No comments

Related manuals for A7500 Series

Brand: Hama Pages: 5

SuperStack 3 4900

Brand: 3Com Pages: 2

Brand: IDEC Pages: 8

Brand: IDEM SAFETY SWITCHES Pages: 2

Brand: Zigen Pages: 40

Brand: Zigen Pages: 4

Brand: ORiNG Pages: 2

Brand: Ruby Tech Pages: 2

Brand: Datavideo Pages: 64

Brand: LEGRAND Pages: 4

LMP-0602 24-V2 Series

Brand: ANTAIRA Pages: 2

Brand: Key Digital Pages: 20

Brand: Lantech Pages: 29

Brand: TRENDnet Pages: 2

Brand: Edimax Pages: 2

Brand: Gefen Pages: 12

Brand: D+H Pages: 16

Brand: Scion-Tech Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands