manualshive.com logo in svg

HP A7500 Series, Command Reference Manual

The HP A7500 Series Configuration Manual is a comprehensive resource for users looking to optimize the performance of their HP A7500 Series product. This manual can be easily downloaded for free from manualshive.com, providing step-by-step instructions and valuable insights for efficient configuration and enhanced functionality.

Share
Download
background image

 

202 

The default operating mode of an EB, SC, SD, or SRP2XBSLAVE card is 

normal

. 

 

 

NOTE: 

•

 

After setting the operating mode of an EB, SC, or SD card, save the configuration and reboot the switch
to validate the setting.  

•

 

If your switch has multiple EB or SD cards, set the same operating mode for them.  

•

 

An EB or SD card might reboot once or twice for self-optimization the first time you change its operating
mode or upgrade the software version of the switch after changing the card operating mode. The 

process takes about 6 to 10 minutes. 

 

Examples 

# Set the EB card in slot 2 of the A7502 switch to operate in bridging mode. 

<Sysname> system-view 

[Sysname] switch-mode bridging slot 2 

# Restore the default operating mode of the EB card in slot 2 of the A7502 switch. 

<Sysname> system-view 

[Sysname] undo switch-mode slot 2 

switch-mode optional-proxy-board 

Syntax 

In standalone mode:  

switch-mode

 

optional-proxy-board 

undo switch-mode

 

optional-proxy-board

 

In IRF mode:  

switch-mode optional-proxy-board chassis 

chassis-number 

undo switch-mode optional-proxy-board chassis 

chassis-number 

View 

System view 

Default level 

2: System level 

Parameters 

chassis 

chassis-number

: Specifies an IRF member switch. The 

chassis-number

 argument represents the IRF 

member ID of the switch. (In IRF mode) 

Description 

Use the 

switch-mode optional-proxy-board 

command to enable LPU forwarding proxy.  

Use the 

undo switch-mode

 

optional-proxy-board 

command to disable LPU forwarding proxy.  

By default, LPU forwarding proxy is disabled. If the switch has two MPUs, the active MPU can forward or 

process traffic for LPUs. 
If LPU forwarding proxy is enabled, the switch sets one high-performance LPU instead of using the active 
MPU to forward traffic for overloaded LPUs or provide extended services. 

Summary of Contents for A7500 Series































































































































































































































Reviews:

No comments

Related manuals for A7500 Series

La Toulousaine 1400 Installation Manual preview
1400
Brand: La Toulousaine Pages: 6
IBM 8275-416 User Manual preview
8275-416
Brand: IBM Pages: 156
KanexPro MX-HDBT8X818G Manual preview
MX-HDBT8X818G
Brand: KanexPro Pages: 16
CalDigit Super Share Quick Start Manual preview
Super Share
Brand: CalDigit Pages: 13
CTS FOS-3124 SERIES User Manual preview
FOS-3124 SERIES
Brand: CTS Pages: 223
S+S Regeltechnik Premasreg 716 Series Operating Instructions, Mounting & Installation preview
Premasreg 716 Series
Brand: S+S Regeltechnik Pages: 32
Z-Band ZBT0100052 User Manual And Installation Manual preview
ZBT0100052
Brand: Z-Band Pages: 13
GE Digital Energy STS-400-25-3 Installation And Operating Manual preview
Digital Energy STS-400-25-3
Brand: GE Pages: 49
N-Tron 100-POE4-MDR User Manual & Installation Manual preview
100-POE4-MDR
Brand: N-Tron Pages: 17
Elements LINQ LQ48006 Product Manual preview
LINQ LQ48006
Brand: Elements Pages: 2
Kobold TDD Operating Instructions Manual preview
TDD
Brand: Kobold Pages: 23
S&S Northern Merlin CS1 User Manual preview
Merlin CS1
Brand: S&S Northern Pages: 8
Global Streams GlobeCaster STUDIO 4000 Manual preview
GlobeCaster STUDIO 4000
Brand: Global Streams Pages: 144
MRD TNM4000-TP36FF4X16G24P User Manual preview
TNM4000-TP36FF4X16G24P
Brand: MRD Pages: 38
SICK MSL Series Operating Instructions Manual preview
MSL Series
Brand: SICK Pages: 299
G&D DVIMUX8-USB Installation And Operation Manual preview
DVIMUX8-USB
Brand: G&D Pages: 80
Stahl 128635 Operating Instructions Manual preview
128635
Brand: Stahl Pages: 29
Lantech IPES-2208CA User Manual preview
IPES-2208CA
Brand: Lantech Pages: 146

Brands by name

Popular brands

Load more brands