manualshive.com logo in svg

HP A7500 Series, Command Reference Manual

The HP A7500 Series Configuration Manual is a comprehensive resource for users looking to optimize the performance of their HP A7500 Series product. This manual can be easily downloaded for free from manualshive.com, providing step-by-step instructions and valuable insights for efficient configuration and enhanced functionality.

Share
Download
background image

 

199 

Examples 

# Set the detection interval to 100 seconds. 

<Sysname> system-view 

[Sysname] shutdown-interval 100 

strict-standby enable 

Syntax 

strict-standby enable 
undo strict-standby enable 

View 

System view 

Default level 

2: System level 

Parameters 

None 

Description 

Use the 

strict-standby enable

 command to enable strict standby mode for the network ports on the MPUs. 

Use the 

undo strict-standby enable

 command to disable strict standby mode for the network ports on the 

MPUs.

 

 

 

NOTE: 

The strict-standby setting is applicable only to the A7503, A7506, A7506-V, and A7510 switches that 
use two LSQ1SRP2XB MPUs. 

 

By default, strict standby is disabled, and the network ports on both MPUs can forward traffic regardless 

of the active/standby state of the MPUs. If the standby MPU has a hardware failure, the network ports on 

it might not be able to correctly forward data. 
In strict standby mode, only the network ports on the active MPU can forward traffic. When an 

active/standby switchover occurs between the MPUs, the network ports on the original active MPU go 
down and the network ports on the new active MPU come up to forward traffic.  
You can use the network ports on the MPUs to set up a dual-homed network and enable strict standby 

mode to increase network availability.  

Examples 

# Enable strict standby mode for the network ports on the MPUs. 

<Sysname> system-view 

[Sysname] strict-standby enable 

switch-mode (for MPUs) 

Syntax 

1.

 

For LSQ1SRP1CB 

In standalone mode: 

Summary of Contents for A7500 Series































































































































































































































Reviews:

No comments

Related manuals for A7500 Series

D-Link DUB-1340 Datasheet preview
DUB-1340
Brand: D-Link Pages: 2
D-Link DKVM-4U Specifications preview
DKVM-4U
Brand: D-Link Pages: 2
D-Link DKVM-16 - KVM Switch Manual preview
DKVM-16 - KVM Switch
Brand: D-Link Pages: 24
D-Link Dis-200G Series Web Ui Reference Manual preview
Dis-200G Series
Brand: D-Link Pages: 161
D-Link Dis-200G Series Quick Installation Manual preview
Dis-200G Series
Brand: D-Link Pages: 16
D-Link Dis-200G Series Hw Installation Manual preview
Dis-200G Series
Brand: D-Link Pages: 47
D-Link DGS-3130-30PS Quick Installation Manual preview
DGS-3130-30PS
Brand: D-Link Pages: 25
D-Link DGS-3100 SERIES Hardware Installation Manual preview
DGS-3100 SERIES
Brand: D-Link Pages: 54
D-Link DGS-3100 SERIES Cli Manual preview
DGS-3100 SERIES
Brand: D-Link Pages: 220
D-Link DGS-3000-28SC Quick Installation Manual preview
DGS-3000-28SC
Brand: D-Link Pages: 24
D-Link DGS-1248T - Switch Manual preview
DGS-1248T - Switch
Brand: D-Link Pages: 52
D-Link DGS-1216T - Switch Getting Started Manual preview
DGS-1216T - Switch
Brand: D-Link Pages: 42
D-Link DGS-1216T - Switch Quick Installation Guid preview
DGS-1216T - Switch
Brand: D-Link Pages: 10
D-Link DGS-1010MP Installation Manual preview
DGS-1010MP
Brand: D-Link Pages: 8
D-Link DES-3350SR Command Line Interface Reference Manual preview
DES-3350SR
Brand: D-Link Pages: 379
D-Link DES-3326SR Manual preview
DES-3326SR
Brand: D-Link Pages: 240
D-Link DES-3350SR User Manual preview
DES-3350SR
Brand: D-Link Pages: 188
D-Link DES-3326S - Switch - Stackable User Manual preview
DES-3326S - Switch - Stackable
Brand: D-Link Pages: 349

Brands by name

Popular brands

Load more brands