HP A7500 Series Command Reference Manual Download Page 172

Page: 172 / 222

165

Field Description

State

Status of the card:

•

Absent—No card is in the slot.

•

Master—The card is the active MPU for the IRF fabric.

•

Slave—The card is a standby MPU for the IRF fabric.

•

Normal—The card is operating normally.

•

Fault—The card is in an error condition.

Subslot

Maximum number of subcards that the card supports

Soft Ver

Software version running on the card

Patch Ver

Version of the patch running on the card.

None

indicates that no patch is on the

card.

display device manuinfo

Syntax

In standalone mode:

display device manuinfo

[

slot

slot-number

] [

{

begin

exclude

include

}

regular-expression

]

In IRF mode:

display device manuinfo

[

chassis

chassis-number

[

slot

slot-number

] ] [

{

begin

exclude

include

}

regular-expression

]

View

Any view

Default level

3: Manage level

Parameters

chassis

chassis-number

: Displays the electronic label data for an IRF member switch. The

chassis-number

argument represents the IRF member ID of the switch. If no member switch is specified, the command

displays the electronic label data for all member switches. (In IRF mode)

slot

slot-number

: Displays the electronic label data for a card. The

slot-number

argument represents the

slot number of the card. If no card is specified, the command displays the electrical label data for all

cards.

: Filters command output by specifying a regular expression. For more information about regular

expressions, see

Fundamentals Configuration Guide

begin

: Displays the first line that matches the specified regular expression and all lines that follow.

exclude

: Displays all lines that do not match the specified regular expression.

include

: Displays all lines that match the specified regular expression.

regular-expression

: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Description

Use the

display device manuinfo

command to display electronic label data.

Summary of Contents for A7500 Series































































































































































































































Search results

Summary of Contents for A7500 Series

Reviews:

Related manuals for A7500 Series

Brands by name

Popular brands

HP A7500 Series, Command Reference Manual

Search results

Summary of Contents for A7500 Series

Reviews:

Related manuals for A7500 Series

Brands by name

Popular brands