HP A7500 Series Command Reference Manual Download Page 183

Page: 183 / 222

176

View

Any view

Default level

3: Manage level

Parameters

: Filters command output by specifying a regular expression. For more information about regular

expressions, see

Fundamentals Configuration Guide

begin

: Displays the first line that matches the specified regular expression and all lines that follow.

exclude

: Displays all lines that do not match the specified regular expression.

include

: Displays all lines that match the specified regular expression.

regular-expression

: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Description

Use the

display schedule reboot

command to display the reboot schedule.

In an IRF fabric, the reboot schedule applies to all IRF member switches.
Related commands:

schedule reboot at

and

schedule reboot delay.

Examples

# Display the reboot schedule.

<Sysname> display schedule reboot

System will reboot at 16:00:00 03/10/2010 (in 2 hours and 5 minutes).

display switch-mode status

Syntax

In standalone mode:

display switch-mode status

[

{

begin

exclude

include

}

regular-expression

]

In IRF mode:

display switch-mode status chassis

chassis-number

[

{

begin

exclude

include

}

regular-expression

]

View

Any view

Default level

0: Visit level

Parameters

chassis

chassis-number

: Displays the operating modes of all cards on an IRF member switch. The

chassis-number

argument represents the IRF member ID of a switch. (In IRF mode)

: Filters command output by specifying a regular expression. For more information about regular

expressions, see the

Fundamentals Configuration Guide

begin

: Displays the first line that matches the specified regular expression and all lines that follow.

exclude

: Displays all lines that do not match the specified regular expression.

include

: Displays all lines that match the specified regular expression.

Summary of Contents for A7500 Series































































































































































































































Search results

Summary of Contents for A7500 Series

Reviews:

Related manuals for A7500 Series

Brands by name

Popular brands

HP A7500 Series, Command Reference Manual

Search results

Summary of Contents for A7500 Series

Reviews:

Related manuals for A7500 Series

Brands by name

Popular brands