HP A7500 Series Command Reference Manual Download Page 29

Page: 29 / 222

A : Authentication use AAA.

L : Authentication use local database.

N : Current UI need not authentication.

P : Authentication use current UI's password.

Table 1

Output description

Field Description

The current user interface is active.

The current user interface is active and works in asynchronous mode.

Idx

Absolute number of the user interface.

Type

Type and relative number of the user interface.

Tx/Rx

Transmission/Receive rate of the user interface

Modem

Whether the modem is allowed to dial in (in), dial out (out), or both (inout)
By default, the character - is displayed to indicate that this function is disabled.

Privi

Indicates the command level of a user under that user interface

Auth

Authentication mode for the users, which can be A, P, L, and N.

Int

The physical port that corresponds to the user interface. (For AUX and VTY user interfaces,
- is displayed.)

A AAA

authentication

Local authentication (not supported)

N No

authentication

P Password

authentication

# Display summary about all user interfaces.

<Sysname> display user-interface summary

User interface type : [AUX]

0:UX

User interface type : [VTY]

18:UXXX XXXX XXXX XXXX

2 character mode users. (U)

16 UI never used. (X)

2 total UI in use

Table 2

Output description

Field Description

User interface type

Type of user interface (AUX/VTY)

0:X

0 represents the absolute number of the user interface. X means this
user interface is not used; U means this user interface is in use.

character mode users. (U)

Number of users, or, the total number of character U.

UI never used. (X)

Number of user interfaces not used, or, the total number of
character X.

Summary of Contents for A7500 Series































































































































































































































Search results

Summary of Contents for A7500 Series

Reviews:

Related manuals for A7500 Series

Brands by name

Popular brands

HP A7500 Series, Command Reference Manual

Search results

Summary of Contents for A7500 Series

Reviews:

Related manuals for A7500 Series

Brands by name

Popular brands