manualshive.com logo in svg

HP A7500 Series, Command Reference Manual

The HP A7500 Series Configuration Manual is a comprehensive resource for users looking to optimize the performance of their HP A7500 Series product. This manual can be easily downloaded for free from manualshive.com, providing step-by-step instructions and valuable insights for efficient configuration and enhanced functionality.

Share
Download
background image

 

204 

reboot

: Specifies that when a software exception occurs on an MPU, the switch automatically reboots the 

MPU to recover it from the error condition. 

Description 

Use the 

system-failure

 command to configure the software exception handling method for MPUs. 

By default, an MPU reboots to recover from a software exception condition.  
In an IRF fabric, the software exception handling method applies to all member switches.  

 

 

NOTE: 

An LPU always reboots to recover from a software exception condition.  

 

Examples 

# Set the software exception handling method to reboot for MPUs. 

<Sysname> system-view 

[Sysname] system-failure reboot 

temperature-limit 

Syntax 

In standalone mode:

 

temperature-limit

 

slot 

slot-number

 

hotspot 

sensor-number

 

lowerlimit warninglimit 

[ 

alarmlimit

 ] 

undo temperature-limit slot 

slot-number

 

hotspot 

sensor-number 

In IRF mode: 

temperature-limit

 

chassis

 

chassis-number

 

slot 

slot-number

   

hotspot 

sensor-number

 

lowerlimit 

warninglimit 

[ 

alarmlimit

 ] 

undo temperature-limit chassis

 

chassis-number

 

slot 

slot-number

 

hotspot 

sensor-number 

 

View 

System view 

Default level 

2: System level 

Parameters 

chassis 

chassis-number

: Specifies an IRF member switch. The 

chassis-number

 argument represents the IRF 

member ID of the switch. (In IRF mode)

 

slot 

slot-number

: Specifies a card in the specified switch. The 

slot-number

 argument represents the slot 

number of the card.  

hotspot

: Specifies a hotspot sensor. Hotspot sensors are placed near major heat sources, for example, 

chips, to monitor their temperature.

 

sensor-number

: Specifies a sensor number, an integer that increases from 1.  

lowerlimit

: Low temperature threshold in Celsius degrees. The value ranges from –5°C to +5°C (23°F to 

41°F). 

Summary of Contents for A7500 Series































































































































































































































Reviews:

No comments

Related manuals for A7500 Series

NEC 2400 Integration Manual preview
2400
Brand: NEC Pages: 168
A SYSTEMS AV50 User Manual preview
AV50
Brand: A SYSTEMS Pages: 16
Qlogic SANbox 5802V User Manual preview
SANbox 5802V
Brand: Qlogic Pages: 135
Qlogic SANbox2 SANbox2-64 User Manual preview
SANbox2 SANbox2-64
Brand: Qlogic Pages: 224
Hama Data Switch Operating Instruction preview
Data Switch
Brand: Hama Pages: 10
StarTech.com MSTCDP122DP Quick Start Manual preview
MSTCDP122DP
Brand: StarTech.com Pages: 2
NBase Communications NH2001M Installation And User Manual preview
NH2001M
Brand: NBase Communications Pages: 72
Sunix ESW-5162GP User Manual preview
ESW-5162GP
Brand: Sunix Pages: 55
Milestone pro MP-SU21T-KVM User Manual preview
MP-SU21T-KVM
Brand: Milestone pro Pages: 32
Wyrestorm MX-0404-H2 Quick Start Manual preview
MX-0404-H2
Brand: Wyrestorm Pages: 4
hager HIC4 Series Operating Instructions Manual preview
HIC4 Series
Brand: hager Pages: 72
Transition Networks SM24-1000SFP-AH Installation Manual preview
SM24-1000SFP-AH
Brand: Transition Networks Pages: 76
Gefen HDMI-242 User Manual preview
HDMI-242
Brand: Gefen Pages: 12
I-Rocks IR-4650 Quick Installation Manual preview
IR-4650
Brand: I-Rocks Pages: 18
CAMDEN Sure-Wave CM-330/N Installation Instructions preview
Sure-Wave CM-330/N
Brand: CAMDEN Pages: 4
Cabletron Systems CyberSWITCH CSX150 User Manual preview
CyberSWITCH CSX150
Brand: Cabletron Systems Pages: 620
Accton Technology 24/48 10/100 Ports + 2GE Management Manual preview
24/48 10/100 Ports + 2GE
Brand: Accton Technology Pages: 512
N-Tron 7014FX2 User Manual & Installation Manual preview
7014FX2
Brand: N-Tron Pages: 152

Brands by name

Popular brands

Load more brands