HP A7500 Series Command Reference Manual Download Page 15

Page: 15 / 222

2: System level (in other views)

Parameters

None

Description

Use the

quit

command to return to a lower-level view.

In user view, the

quit

command terminates the connection and reconnects to the switch.

Examples

# Switch from GigabitEthernet 2/0/1 interface view to system view, and then to user view.

[Sysname-GigabitEthernet2/0/1] quit

[Sysname] quit

return

Syntax

return

View

Any view except user view

Default level

2: System level

Parameters

None

Description

Use the

return

command to return to user view from the current view, which can also be done with the hot

key

Ctrl+Z

Related commands:

quit

Examples

# Return to user view from GigabitEthernet 2/0/1 view.

[Sysname-GigabitEthernet2/0/1] return

screen-length disable

Syntax

screen-length disable
undo screen-length disable

View

User view

Default level

1: Monitor level

Summary of Contents for A7500 Series































































































































































































































Search results

Summary of Contents for A7500 Series

Reviews:

Related manuals for A7500 Series

Brands by name

Popular brands

HP A7500 Series, Command Reference Manual

Search results

Summary of Contents for A7500 Series

Reviews:

Related manuals for A7500 Series

Brands by name

Popular brands