HP A7500 Series Command Reference Manual Download Page 46

Page: 46 / 222

telnet client source

Syntax

telnet client source

{

interface

interface-type interface-number

ip-address

}

undo telnet client source

View

System view

Default level

2: System level

Parameters

interface

interface-type interface-number

: Specifies the source interface. The source IPv4 address of the

Telnet packets sent is the IPv4 address of the specified interface.

interface-type interface-number

represents the interface type and number.

ip-address

: Specifies the source IPv4 address of Telnet packets.

Description

Use the

telnet client source

command to specify the source IPv4 address or source interface for sending

Telnet packets when the device serves as a Telnet client.
Use the

undo telnet client source

command to remove the source IPv4 address or source interface for

sending Telnet packets.
By default, no source IPv4 address or source interface for sending Telnet packets is specified. The source

IPv4 address is selected by routing.
The source IPv4 address or source interface specified by this command is applicable all Telnet

connections.
If you use both this command and the

telnet

command to specify the source IPv4 address or source

interface, the source IPv4 address or interface specified by the

telnet

command takes effect.

Related commands:

display telnet client configuration

Examples

# Specify the source IPv4 address for sending Telnet packets when the device serves as a Telnet client as

1.1.1.1.

<Sysname> system-view

[Sysname] telnet client source ip 1.1.1.1

telnet ipv6

Syntax

telnet

ipv6

remote-host

[

-i

interface-type

interface-number

] [

port-number

] [

vpn-instance

vpn-instance-name

]

View

User view

Default level

0: Visit level

Summary of Contents for A7500 Series































































































































































































































Search results

Summary of Contents for A7500 Series

Reviews:

Related manuals for A7500 Series

Brands by name

Popular brands

HP A7500 Series, Command Reference Manual

Search results

Summary of Contents for A7500 Series

Reviews:

Related manuals for A7500 Series

Brands by name

Popular brands