manualshive.com logo in svg

HP 6125G, Command Reference Manual

The HP 6125G Configuration Manual is available for download from our website, providing users with a comprehensive guide to set up and customize their HP 6125G product. This manual is available for free, ensuring easy access to essential instructions and information.

Share
Download
background image

16 

Examples 

# Specify to allow GigabitEthernet 1/0/1 in VLAN 2 to join up to 10 multicast groups. 

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] igmp-snooping group-limit 10 vlan 2 

igmp-snooping group-policy 

Syntax 

igmp-snooping group-policy

 

acl-number

 [ 

vlan

 

vlan-list

 ] 

undo igmp-snooping group-policy

 [ 

vlan

 

vlan-list

 ] 

View 

Layer 2 Ethernet interface view, Layer 2 aggregate interface view 

Default level 

2: System level 

Parameters 

acl-number

: Specifies a basic or advanced ACL number, in the range of 2000 to 3999. The source 

address or address range specified in the advanced ACL rule matches the multicast source address or 

addresses specified in IGMPv3 reports, rather than the source address in the IP packets. The system 
assumes that an IGMPv1 or IGMPv2 report or an IGMPv3 IS_EX and TO_EX report that does not carry 

a multicast source address carries a multicast source address of 0.0.0.0. 

vlan 

vlan-list

: Specifies one or multiple VLANs. You can provide up to 10 VLAN lists. For each list, you 

can specify an individual VLAN in the form of 

vlan-id

, or a VLAN range in the form of 

start-vlan-id

 

to

 

end-vlan-id

, where the end VLAN ID must be greater than the start VLAN ID. The value range of a VLAN 

ID is 1 to 4094. 

 

Description 

Use 

igmp-snooping group-policy 

to configure a multicast group filter on the current port, namely, to 

control the multicast groups that the hosts on the port can join.  
Use 

undo igmp-snooping group-policy

 to remove a multicast group filter.  

By default, no multicast group filter is configured on an interface. Namely, a host can join any valid 

multicast group. 
If you do not specify any VLAN when using this command in Layer 2 Ethernet interface view or Layer 2 
aggregate interface view, the command takes effect for all VLANs that the interface belongs to. If you 

specify one or more VLANs, the command takes effect for the specified VLANs that the interface belongs 

to.  
If the specified ACL does not exist or the ACL rule is null, all multicast groups are filtered out.  
You can configure different ACL rules for a port in different VLANs. For a given VLAN, a newly 

configured ACL rule overrides the existing one.  
Related commands: 

group-policy

.  

Examples 

# Apply ACL 2000 as a multicast group filter so that hosts on GigabitEthernet 1/0/1 in VLAN 2 can join 

225.1.1.1 only.  

<Sysname> system-view 

Summary of Contents for 6125G











































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 6125G

IBM N Series Installation And Configuration Instructions preview
N Series
Brand: IBM Pages: 7
IBM 88631SU - System x3850 - 8863 Installation Manual preview
88631SU - System x3850 - 8863
Brand: IBM Pages: 90
Quatech AirborneDirect ABDG-SE-IN5410 Quick Start Manual preview
AirborneDirect ABDG-SE-IN5410
Brand: Quatech Pages: 8
ANTAIRA STW-611C Installation Manual preview
STW-611C
Brand: ANTAIRA Pages: 2
t.a.c. TAC Xenta 511 Handbook preview
TAC Xenta 511
Brand: t.a.c. Pages: 36
QNAP TS-130 User Manual preview
TS-130
Brand: QNAP Pages: 39
IBM BladeCenter HS22 Supplementary Manual preview
BladeCenter HS22
Brand: IBM Pages: 1
IBM 88728RU Specifications preview
88728RU
Brand: IBM Pages: 4
IBM eServer 250 xSeries Installation Manual preview
eServer 250 xSeries
Brand: IBM Pages: 84
IBM 8682 - Eserver xSeries 350 Hardware Maintenance Manual preview
8682 - Eserver xSeries 350
Brand: IBM Pages: 174
IBM 325 8639 Hardware Maintenance Manual preview
325 8639
Brand: IBM Pages: 145
IBM B50 User Manual preview
B50
Brand: IBM Pages: 221
Planet FPS-1101 User Manual preview
FPS-1101
Brand: Planet Pages: 83
PRG MBOX EXTREME User Manual preview
MBOX EXTREME
Brand: PRG Pages: 136
Gigabyte R272-P32 User Manual preview
R272-P32
Brand: Gigabyte Pages: 86
Gigabyte G492-HA0 User Manual preview
G492-HA0
Brand: Gigabyte Pages: 110
Gigabyte R283-Z93-AAF1 User Manual preview
R283-Z93-AAF1
Brand: Gigabyte Pages: 173
Gigabyte H273-Z81-AAN1 User Manual preview
H273-Z81-AAN1
Brand: Gigabyte Pages: 166

Brands by name

Popular brands

Load more brands