manualshive.com logo in svg

HP 6125G, Command Reference Manual

The HP 6125G Configuration Manual is available for download from our website, providing users with a comprehensive guide to set up and customize their HP 6125G product. This manual is available for free, ensuring easy access to essential instructions and information.

Share
Download
background image

 

140 

To use an ACL that does not exist in the group-policy list, you can use the 

acl-number

 argument to specify 

an ACL and set its 

order-value

. This inserts the ACL to the position of 

order-value

 in the group-policy list. 

If you do not include the 

order

 

order-value

 option in your command, the ACL is appended to the end of 

the group-policy list.  
If you use this command multiple times on the same multicast group, the first traffic rate configuration 

matched in sequence takes effect.  
If the switch is an RP, disabling switchover to SPT might cause multicast traffic forwarding failures on the 

source-side DR. When disabling switchover to SPT, be sure you fully understand its impact on your 

network. 

Examples 

# Disable the switchover to SPT on the receiver-side DR.  

<Sysname> system-view 

[Sysname] pim 

[Sysname-pim] spt-switch-threshold infinity 

ssm-policy (PIM view) 

Syntax 

ssm-policy 

acl-number

 

undo ssm-policy 

View 

PIM view 

Default level 

2: System level 

Parameters 

acl-number

: Basic ACL number, in the range of 2000 to 2999.  

Description 

Use 

ssm-policy

 to configure the SSM multicast group range.  

Use 

undo ssm-policy

 to restore the default.  

By default, the SSM group range is 232.0.0.0/8. 
You can use this command to define an address range of permitted or denied multicast groups. If the 

match succeeds, the multicast mode is PIM-SSM. Otherwise, the multicast mode is PIM-SM.  

Examples 

# Configure the SSM group range to be 232.1.0.0/16.  

<Sysname> system-view 

[Sysname] acl number 2000 

[Sysname-acl-basic-2000] rule permit source 232.1.0.0 0.0.255.255 

[Sysname-acl-basic-2000] quit 

[Sysname] pim 

[Sysname-pim] ssm-policy 2000 

Summary of Contents for 6125G











































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 6125G

IBM Enterprise Server S80 User Manual preview
Enterprise Server S80
Brand: IBM Pages: 282
Panasonic KX-NCP Series Software Manual preview
KX-NCP Series
Brand: Panasonic Pages: 16
IBM Power 750 Express Hardware Announcement preview
Power 750 Express
Brand: IBM Pages: 86
LaCie 8BIG RACK THUNDERBOLT 2 Quick Start Manual preview
8BIG RACK THUNDERBOLT 2
Brand: LaCie Pages: 28
NEC N8100-1056F User Manual preview
N8100-1056F
Brand: NEC Pages: 408
H3C UniServer R4300 G5 Installation, Quick Start preview
UniServer R4300 G5
Brand: H3C Pages: 16
Fujitsu Siemens Computers PRIMERGY B120 Operating Manual preview
PRIMERGY B120
Brand: Fujitsu Siemens Computers Pages: 68
Ubiquiti UniFi UAS-PRO Quick Start Manual preview
UniFi UAS-PRO
Brand: Ubiquiti Pages: 28
SIERRA VIDEO SYSTEMS Crestron 908012 User Manual preview
Crestron 908012
Brand: SIERRA VIDEO SYSTEMS Pages: 32
Discover Video Devos 4 User Manual preview
Devos 4
Brand: Discover Video Pages: 148
Zeiss 5034555 User Manual preview
5034555
Brand: Zeiss Pages: 12
IBM 8672-26x Manual preview
8672-26x
Brand: IBM Pages: 75
Arista NetVisor UNUM High Capacity Appliance User Manual preview
NetVisor UNUM High Capacity Appliance
Brand: Arista Pages: 81
RCI FP-SER-ETH-SERVR2 User Manual preview
FP-SER-ETH-SERVR2
Brand: RCI Pages: 17
SystemBase Portbase-3010 User Manual preview
Portbase-3010
Brand: SystemBase Pages: 118
Intermec 6950 User Manual preview
6950
Brand: Intermec Pages: 144
Intermec DCS 300 User Manual preview
DCS 300
Brand: Intermec Pages: 452
Polycom ReadiManagerSE200 Brochure preview
ReadiManagerSE200
Brand: Polycom Pages: 4

Brands by name

Popular brands

Load more brands