HP 6125G Command Reference Manual Download Page 81

Page: 81 / 426

Table 19

Command output

Field Description

Group

Multicast group address

Source list

List of multicast source addresses

display igmp ssm-mapping group

Syntax

display igmp

ssm-mapping

group

[

group-address

interface

interface-type

interface-number

]

[

verbose

] [

{

begin

exclude

include

}

regular-expression

]

View

Any view

Default level

1: Monitor level

Parameters

group-address

: Specifies a multicast group by its IP address, in the range of 224.0.1.0 to

239.255.255.255. If you do not specify any multicast group, the command displays the information of

all multicast groups created based on the configured IGMP SSM mappings.

interface

interface-type interface-number

: Specifies an interface by its type and number. If you do not

specify any interface, the command displays the multicast group information created based on the
configured IGMP SSM mappings on all the interfaces.

verbose

: Displays the detailed multicast group information created based on the configured IGMP SSM

mappings.

: Filters command output by specifying a regular expression. For more information about regular

expressions, see

Fundamentals Configuration Guide

begin

: Displays the first line that matches the specified regular expression and all lines that follow.

exclude

: Displays all lines that do not match the specified regular expression.

include

: Displays all lines that match the specified regular expression.

regular-expression

: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Description

Use

display igmp ssm-mapping group

to display the multicast group information created based on the

configured IGMP SSM mappings.

Examples

# Display the detailed information of multicast group 232.1.1.1 created based on the configured IGMP
SSM mappings.

<Sysname> display igmp ssm-mapping group 232.1.1.1 verbose

Interface group report information

Vlan-interface1(10.10.10.10):

Total 1 IGMP SSM-mapping Group reported

Group: 232.1.1.1

Uptime: 00:00:31

Summary of Contents for 6125G











































































































































































































































































































































































































































Search results

Summary of Contents for 6125G

Reviews:

Related manuals for 6125G

Brands by name

Popular brands

HP 6125G, Command Reference Manual

Search results

Summary of Contents for 6125G

Reviews:

Related manuals for 6125G

Brands by name

Popular brands