HP 6125G Command Reference Manual Download Page 275

Page: 275 / 426

263

Description

Use

multicast ipv6 forwarding-table downstream-limit

to configure the maximum number of downstream

nodes for a single entry in the IPv6 multicast forwarding table.
Use

undo multicast ipv6 forwarding-table downstream-limit

to restore the default.

By default, the maximum number of downstream nodes for a single entry in the IPv6 multicast forwarding

table is 128.
Related commands:

display multicast ipv6 forwarding-table

Examples

# Set the maximum number of downstream nodes for a single entry in the IPv6 multicast forwarding table

to 120.

<Sysname> system-view

[Sysname] multicast ipv6 forwarding-table downstream-limit 120

multicast ipv6 forwarding-table route-limit

Syntax

multicast ipv6 forwarding-table route-limit

limit

undo multicast ipv6 forwarding-table route-limit

View

System view

Default level

2: System level

Parameters

limit

: Specifies the maximum number of entries in the IPv6 multicast forwarding table. The value ranges

from 0 to 1000.

Description

Use

multicast ipv6 forwarding-table route-limit

to configure the maximum number of entries in the IPv6

multicast forwarding table.
Use

undo multicast ipv6 forwarding-table route-limit

to restore the default.

By default, the upper limit is 1000.
Related commands:

display multicast ipv6 forwarding-table

Examples

# Set the maximum number of entries in the IPv6 multicast forwarding table to 200.

<Sysname> system-view

[Sysname] multicast ipv6 forwarding-table route-limit 200

multicast ipv6 load-splitting

Syntax

multicast ipv6 load-splitting

{

source

source-group

}

undo multicast ipv6 load-splitting

Summary of Contents for 6125G











































































































































































































































































































































































































































Search results

Summary of Contents for 6125G

Reviews:

Related manuals for 6125G

Brands by name

Popular brands

HP 6125G, Command Reference Manual

Search results

Summary of Contents for 6125G

Reviews:

Related manuals for 6125G

Brands by name

Popular brands