HP 6125G Command Reference Manual Download Page 89

Page: 89 / 426

igmp proxying forwarding

Syntax

igmp proxying forwarding
undo igmp proxying forwarding

View

Interface view

Default level

2: System level

Parameters

None

Description

Use

igmp proxying forwarding

to enable a non-querier downstream interface to forward multicast traffic.

Use

undo igmp proxying forwarding

to disable the forwarding capability of a non-querier downstream

interface.
By default, a non-querier downstream interface does not forward multicast traffic.

Examples

# Enable the multicast forwarding capability on VLAN-interface 100, a non-querier downstream

interface on the IGMP proxy switch.

<Sysname> system-view

[Sysname] interface vlan-interface 100

[Sysname-Vlan-interface100] igmp proxying forwarding

igmp require-router-alert

Syntax

igmp require-router-alert
undo igmp require-router-alert

View

Interface view

Default level

2: System level

Parameters

None

Description

Use

igmp require-router-alert

to configure the interface to discard IGMP messages that do not carry the

Router-Alert option.
Use

undo igmp require-router-alert

to restore the default.

By default, the switch does not check the Router-Alert option but passes all the IGMP messages that it

receives to the upper layer protocol for processing.

Summary of Contents for 6125G











































































































































































































































































































































































































































Search results

Summary of Contents for 6125G

Reviews:

Related manuals for 6125G

Brands by name

Popular brands

HP 6125G, Command Reference Manual

Search results

Summary of Contents for 6125G

Reviews:

Related manuals for 6125G

Brands by name

Popular brands