manualshive.com logo in svg

HP 6125G, Command Reference Manual, Page: 50 / 426

Share
Download
HP 6125G Command Reference Manual Download Page 50

 

38 

Table 5

 

Command output 

Field Description 

subvlan list 

List of sub-VLANs of the multicast VLAN 

port list 

Port list of the multicast VLAN 

 

multicast-vlan 

Syntax 

multicast-vlan 

vlan-id

 

undo multicast-vlan

 { 

all

 | 

vlan-id

 }

 

View 

System view 

Default level 

2: System level 

Parameters 

vlan-id

: Specifies a VLAN by its ID, in the range of 1 to 4094.  

all

: Specifies all multicast VLANs. 

Description 

Use 

multicast-vlan

 to configure the specified VLAN as a multicast VLAN and enter multicast VLAN view.  

Use 

undo multicast-vlan 

to remove the specified VLAN as a multicast VLAN. 

The VLAN to be configured is not a multicast VLAN by default.  
The specified VLAN to be configured as a multicast VLAN must exist.  
The multicast VLAN feature cannot be enabled on a device with IP multicast routing enabled.  
For a sub-VLAN-based multicast VLAN, you must enable IGMP snooping only in the multicast VLAN. For 

a port-based multicast VLAN, you must enable IGMP snooping in both the multicast VLAN and all the 
user VLANs.  
Related commands: 

igmp-snooping enable

 and 

multicast routing-enable

.  

Examples 

# Enable IGMP snooping in VLAN 100. Configure it as a multicast VLAN and enter multicast VLAN view.  

<Sysname> system-view 

[Sysname] igmp-snooping 

[Sysname-igmp-snooping] quit 

[Sysname] vlan 100 

[Sysname-vlan100] igmp-snooping enable 

[Sysname-vlan100] quit 

[Sysname] multicast-vlan 100 

[Sysname-mvlan-100] 

Summary of Contents for 6125G











































































































































































































































































































































































































































Reviews:

No comments