HP 6125G Command Reference Manual Download Page 91

Page: 91 / 426

igmp send-router-alert

Syntax

igmp send-router-alert
undo igmp send-router-alert

View

Interface view

Default level

2: System level

Parameters

None

Description

Use

igmp send-router-alert

to enable insertion of the Router-Alert option in IGMP messages to send

through a port.
Use

undo igmp send-router-alert

to disable insertion of the Router-Alert option in IGMP messages to

send through a port.
By default, IGMP messages are sent with the Router-Alert option.
Related commands:

igmp require-router-alert

and

send-router-alert

Examples

# Disable insertion of the Router-Alert option into IGMP messages that leave VLAN-interface 100.

<Sysname> system-view

[Sysname] interface vlan-interface 100

[Sysname-Vlan-interface100] undo igmp send-router-alert

igmp ssm-mapping enable

Syntax

igmp ssm-mapping enable
undo igmp ssm-mapping enable

View

Interface view

Default level

2: System level

Parameters

None

Description

Use

igmp ssm-mapping enable

to enable the IGMP SSM mapping feature on the current interface.

Use

undo igmp ssm-mapping enable

to disable the IGMP SSM mapping feature on the current interface.

By default, the IGMP SSM mapping feature is disabled on all interfaces.

Summary of Contents for 6125G











































































































































































































































































































































































































































Search results

Summary of Contents for 6125G

Reviews:

Related manuals for 6125G

Brands by name

Popular brands

HP 6125G, Command Reference Manual

Search results

Summary of Contents for 6125G

Reviews:

Related manuals for 6125G

Brands by name

Popular brands