manualshive.com logo in svg

HP 6125G, Command Reference Manual, Page: 371 / 426

Share
Download
HP 6125G Command Reference Manual Download Page 371

 

359

 

View 

IPv6 MBGP address family view 

Default level 

2: System level

 

Parameters 

None 

Description 

Use 

compare-different-as-med

 to enable the comparison of the MED for paths from peers in different 

ASs.  
Use 

undo compare-different-as-med

 to disable the comparison. 

By default, MED comparison is not allowed among the routes from the peers in different ASs. 
If several paths are available for one destination, the path with the smallest MED is selected. 
Do not use this command unless associated ASs adopt the same IGP and routing selection method. 

Examples 

# In IPv6 MBGP address family view, enable the comparison of the MED for paths from peers in different 
ASs. 

<Sysname> system-view 

[Sysname]bgp 100 

[Sysname-bgp]ipv6-family multicast 

[Sysname-bgp-af-ipv6-mul]compare-different-as-med 

dampening (IPv6 MBGP address family view) 

Syntax 

dampening

  [

 half-life-reachable half-life-unreachable reuse suppress ceiling 

| 

route-policy

 

route-policy-name 

] * 

undo dampening 

View 

IPv6 MBGP address family view 

Default level 

2: System level

 

Parameters 

half-life-reachable

: Specifies the half-life for reachable routes, in the range of 1 to 45 minutes. By default, 

the value is 15 minutes. 

half-life-unreachable

: Specifies the half-life for unreachable routes, in the range of 1 to 45 minutes. By 

default, the value is 15 minutes. 

reuse

: Specifies the reuse threshold value for suppressed routes, in the range of 1 to 20000. A 

suppressed route that has the penalty value decreased under the value is reused. By default, the value is 

750.  

Summary of Contents for 6125G











































































































































































































































































































































































































































Reviews:

No comments