manualshive.com logo in svg

HP 6125G, Command Reference Manual, Page: 84 / 426

Share
Download
HP 6125G Command Reference Manual Download Page 84

 

72

 

Parameters 

None 

Description 

Use 

igmp

 to enter IGMP view.  

Use 

undo igmp

 to remove configurations in IGMP view. 

IP multicast routing must be enabled before this command can take effect.  
Related commands: 

igmp enable

 and 

multicast routing-enable

.  

Examples 

# Enable IP multicast routing and enter IGMP view.  

<Sysname> system-view 

[Sysname] multicast routing-enable 

[Sysname] igmp 

[Sysname-igmp] 

igmp enable 

Syntax 

igmp enable 
undo

 

igmp enable

 

View 

Interface view 

Default level 

2: System level 

Parameters 

None 

Description 

Use 

igmp enable

 to enable IGMP on the current interface.  

Use 

undo igmp enable

 to disable IGMP on the current interface.  

By default, IGMP is disabled on all interfaces.  
IP multicast routing must be enabled before this command can take effect.  
IGMP must be enabled on an interface before any other IGMP feature configured on the interface can 

take effect.  
Related commands: 

igmp

 and 

multicast routing-enable

.  

Examples 

# Enable IP multicast routing, and then enable IGMP on VLAN-interface 100.  

<Sysname> system-view 

[Sysname] multicast routing-enable 

[Sysname] interface vlan-interface 100 

[Sysname-Vlan-interface100] igmp enable 

Summary of Contents for 6125G











































































































































































































































































































































































































































Reviews:

No comments