HP 6125G Command Reference Manual Download Page 148

Page: 148 / 426

136

View

PIM view

Default level

2: System level

Parameters

acl-number

: Advanced ACL number, in the range of 3000 to 3999. The RP can accept only register

messages that match the

permit

statement of the ACL.

Description

Use

to configure an ACL rule to filter register messages.

Use

undo register-policy

to remove the configured register filtering rule.

By default, no register filtering rule is configured.
Related commands:

Examples

# Configure the RP to accept only those register messages from multicast sources on the subnet of

10.10.0.0/16 for multicast groups on the subnet of 225.1.0.0/16.

<Sysname> system-view

[Sysname] acl number 3000

[Sysname-acl-adv-3000] rule permit ip source 10.10.0.0 0.0.255.255 destination 225.1.0.0

0.0.255.255

[Sysname-acl-adv-3000] quit

[Sysname] pim

[Sysname-pim] register-policy 3000

Syntax

interval

undo register-suppression-timeout

View

PIM view

Default level

2: System level

Parameters

interval

: Register suppression time in seconds, in the range of 1 to 65535.

Description

Use

to configure the register suppression time.

Use

undo register-suppression-timeout

to restore the default.

By default, the register suppression time is 60 seconds.
Related commands:

probe-interval

and

Summary of Contents for 6125G











































































































































































































































































































































































































































Search results

Summary of Contents for 6125G

Reviews:

Related manuals for 6125G

Brands by name

Popular brands

HP 6125G, Command Reference Manual

Search results

Summary of Contents for 6125G

Reviews:

Related manuals for 6125G

Brands by name

Popular brands