manualshive.com logo in svg

HP 6125G, Command Reference Manual, Page: 25 / 426

Share
Download
HP 6125G Command Reference Manual Download Page 25

13 

[Sysname-igmp-snooping] quit 

[Sysname] vlan 2 

[Sysname-vlan2] igmp-snooping enable 

[Sysname-vlan2] igmp-snooping drop-unknown 

igmp-snooping enable 

Syntax 

igmp-snooping enable 
undo igmp-snooping enable 

View 

VLAN view 

Default level 

2: System level 

Parameters 

None 

Description 

Use 

igmp-snooping enable 

to enable IGMP snooping for a VLAN.  

Use 

undo igmp-snooping

 

enable 

to disable IGMP snooping for a VLAN.  

By default, IGMP snooping is disabled in a VLAN.  
IGMP snooping must be enabled globally before it can be enabled in a VLAN.  
Related commands: 

igmp-snooping

.  

Examples 

# Enable IGMP snooping in VLAN 2.  

<Sysname> system-view 

[Sysname] igmp-snooping 

[Sysname-igmp-snooping] quit 

[Sysname] vlan 2 

[Sysname-vlan2] igmp-snooping enable 

igmp-snooping fast-leave 

Syntax 

igmp-snooping fast-leave

 [ 

vlan

 

vlan-list

 ] 

undo igmp-snooping fast-leave

 [ 

vlan

 

vlan-list

 ] 

View 

Layer 2 Ethernet interface view, Layer 2 aggregate interface view 

Default level 

2: System level 

Summary of Contents for 6125G











































































































































































































































































































































































































































Reviews:

No comments