HP 6125G Command Reference Manual Download Page 49

Page: 49 / 426

Multicast VLAN configuration commands

display multicast-vlan

Syntax

display multicast-vlan

[

vlan-id

] [

{

begin

exclude

include

}

regular-expression

]

View

Any view

Default level

1: Monitor level

Parameters

vlan-id

: Specifies a multicast VLAN, in the range of 1 to 4094. If this argument is not specified, this

command displays information about all multicast VLANs.

: Filters command output by specifying a regular expression. For more information about regular

expressions, see

Fundamentals Configuration Guide

begin

: Displays the first line that matches the specified regular expression and all lines that follow.

exclude

: Displays all lines that do not match the specified regular expression.

include

: Displays all lines that match the specified regular expression.

regular-expression

: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Description

Use

display multicast-vlan

to display information about the specified multicast VLAN.

Examples

# Display information about all multicast VLANs.

<Sysname> display multicast-vlan

Total 2 multicast-vlan(s)

Multicast vlan 100

subvlan list:

vlan 2 4-6

port list:

no port

Multicast vlan 200

subvlan list:

no subvlan

port list:

GE1/0/1 GE1/0/2

Summary of Contents for 6125G











































































































































































































































































































































































































































Search results

Summary of Contents for 6125G

Reviews:

Related manuals for 6125G

Brands by name

Popular brands

HP 6125G, Command Reference Manual

Search results

Summary of Contents for 6125G

Reviews:

Related manuals for 6125G

Brands by name

Popular brands